background image

IRDA BGA Rework Station T862++    User Manual 

Http://www.tech168.cn 

10 

(1)When the area of the chips is below 15mm*15mm, please choose the 

IR-lamp temperature about 160-240

, and choose the lens which 

D=28mm to avoid destroying other places, usually it will take you 

about 20-40seconds.   

(2)When the area of the chips is between 15mm*15mm and 30mm*30mm, 

please choose the IR-lamp temperature about 240-320

, and choose the 

lens which D=38mm to avoid destroying other places, usually it will 

take you about 30-60seconds. 

(3)When the area of the chips is above 30mm*30mm, please choose the 

IR-lamp temperature 350

Attention: you should turn on the pre-heat 

dish first, and set-up the temperature about 150-200

,wait 3-5minutes 

to allow the temperature steady on the set-up temperature),and choose 

the lens which D=48mmto avoid destroying other places, and keep the 

lamp body direct light. You should control the time carefully to avoid 

burning the chips. 

5

Adjust the focus. The minimum focal diameter of infrared lamp body is   

15mm; the maximum is above 30mm, adjust them according to different   

chips. Usually, the ideal height between lamp and the chip is 20-30mm.   

Adjust the focusing knob by the size of the chip. Ideally, the bright spot   

should cover the whole chip.   

6

Turn on the two switches on the front panel for the pre heating plate and 

the infrared lamp.   

Summary of Contents for T862++
















Reviews: