background image

 

Decrease volume

 WAV 

and MID files are sometimes of 
poor quality. Therefore distortion 
and noise are easily noticed on 
high quality systems. Try a 
different audio source(e.g. CD 
Player)

Volume level on a connected 
device is set too high.

Sound source is distorted.

Check whether the battery power is run 
out and replace the new battery

Sound is distorted

Remote control doesn’t work

Kit Contents

Specifications

       1.5- meter detachable power cord

1pc.

3-meter Active Speaker-passive  interconnect cable          1pc.
1.8-meter 3.5mm-3.5mm audio interconnect cable             1pc.
1.8-meter RCA-RCA audio interconnect cable

1pc.

Instruction manual                                                                   1pc.

       25mm(1”) TWG faceplate, silk dome

       Power Requirements & consumption:

 

Bluetooth

 

 profiles:

       Connectivity wireless:

       Connectivity wired:

    Frequency Re/- 3dB): 

       Built-in Amplifier:

       Bass/Midrange Driver:

       High-Frequency Driver:

       Dimensions(HxWxD):

       Net Weight:

       76mm(3”), TPAIC Reinforced paper cone,TAVS

       2x18W RMS/65W Dynamic Peak 
       HPCDA Class D 

       60Hz-20kHz

       Digital-Coaxial, 3.5mm stereo jack, 
       RCA stereo, USB, SD/MMC card

       Advanced Audio Distribution Profile (A2DP)

      AVRCP, GAVDP

       Active Speaker: 2 kg /pc; Passive: 1.8 kg / pc

       AC 220~240V/50Hz; 100W

       20 x 11.6x 16 cm

Troubleshooting

If the unit fails to operate normally, check the following points to determine 
whether the fault can be corrected. If it cannot be corrected, or if the fault is 
not listed in the Problem column, disconnect the power cord and contact your 
authorized dealer or service centre for help.

Problem

Cause/Remedy

No power when unit is turned on

No sound

Switch on the electric current at the 
socket
Check that the plug has been 
correctly inserted into the socket

.

The internal fuse has blown and 
must be replaced by a qualified 
service technician
The power cord has been 
damaged and must be replaced

.

Input selection is

 

not

 

correct

.

Ensure input selection is set to the 
correct source

Input source volume is low.

Increase the volume level on the 
source device

.

No volume or low volume.

 

Turn the volume control to increase
 the volume level

.

10

9

Bluetooth  

 is a registered trademark of Bluetooth SIG,Inc.

We reserve the right to change the technical data and the design of the product 
without notice as a result of further development.

®

®

 

Bluetooth

®

  

v4.0

Summary of Contents for iMPACT 2.0







Reviews: