TAG Heuer HL 2-33 Manual Download Page 10

Page: 10 / 12

R:\Timing\PRODUITS\HL2-33\EN\HL2-33_EN_02-09.doc

12.02.2009

Page 10 / 12

TECHNICAL SPECIFICATIONS

Principle

High frequency infra-red (50 KHz)

Detection of signal by frequency
discrimination

Distance for use

40 Meters (131 ft.) in "LOW" position

80 Meters (262 ft.) in "HIGH" position

Output impulse adjustable

By optocouplers and working contact.
Impulse

from 1/100 sec. to 2 seconds

Working temperature

- 20°C to + 50°C (-4°F to 122°F)

External power supply

6 – 12V DC, max. current 100 mA

Internal power

2 x 3 batteries 1.5 V "Alkaline"

Type AA Energizer LR6

Power reserve in "LOW" pos

100 hours at 20°C (68°F)

50 hours at -20°C (-4°F)

Power reserve in "HIGH" pos.

50 hours at 20°C (68°F)

20 hours at -20°C (-4°F)

LED Checks

- State of batteries
- Alignment
-

ode

scillator

tatus

Precision of repetitive impulsions

+/- 0.02 ms

Dimensions

2 cases of 160 x 160 x 40 mm (6 x 6 x 1,5
inches)

Weight (incl. batteries)

800 gr (29 ounces) transmitter / receiver

Mounting

with supports ref. HL4-3 or tripods

(1/4 " camera thread)

Summary of Contents for HL 2-33













Search results

Summary of Contents for HL 2-33

Reviews:

Brands by name

Popular brands

TAG Heuer HL 2-33, Manual

Search results

Summary of Contents for HL 2-33

Reviews:

Brands by name

Popular brands