manualshive.com logo in svg

Tadiran Telecom TGW4 SERIES, User Configuration Manual

Share
Download
Tadiran Telecom TGW4 SERIES User Configuration Manual Download Page 107

TGW4/8 Gateway Series for Aeonix                                                                              High Availability Configuration Guide 

Tadiran Telecom (TTL) L.P.                                                                                                                                                           

95

 

4.1.2 Line Configuration 

1.

 

Click the 

Line > Phone number

 tab. 

For detailed information, see 

Phone Number

 on page 

26

. 

a)

 

Fill in the Aeonix telephone numbers (Alias) FXS connected to the TGW gateway.   
(The dial numbers used by Aeonix) 

2.

 

Click the 

Line > Feature

 tab. 

For detailed information, see 

Subscriber Line Features

 on page 

27

. 

a)

 

From the 

Phone ID

 drop-down list, select 

FXS line number

. 

b)

 

In the 

Phone number

 box, fill in the Aeonix telephone numbers (Alias)  FXS connected to 

this port. (The dial numbers used by Aeonix.) 

Summary of Contents for TGW4 SERIES















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands