6
EN
55mm Coil Nailer FCN55V
Congratulations!
On the purchase of your Tacwise power tool. Your tool will perform
to your satisfaction for a long time if handled in accordance with our
Safety and Operating instructions.
Save this manual for future reference
Technical Data
Characteristic
Value
Minimum operating air pressure 70psi
Maximum operating air pressure 120psi
Nail length range
25mm (1") - 57mm (2 1/4")
Nail size
2.1-2.5 Flat & Conical Nails
Magazine capacity
300-350pcs
Air inlet
1/4" NPT
Air consumption
0.62 CFM @ 90psi
Weight
2.4kgs (5.3lbs)
Vibration emission level*
2.6m/s
2
* The declared vibration emission level represents the main applications
of the tool. However if the tool is used for different applications, with
different accessories or poorly maintained, the vibration emission may
differ. This may significantly increase exposure level over the total
working period.
CE – Declaration of Conformity
55mm Coil Nailer FCN55V
Tacwise declares that this power tool has been designed in compliance
with the Regulations and Standards of the
European Directives.
Quality Department, Tacwise Group Plc – UK
WARNING! Before Use Carefully Read And Understand
All Instructions.
Failure to do so could result in fire and/or serious personal injury. For
any queries relating to safety matters on this power tool, please email
.
Unpacking
• Carefully remove the tool and accessories from the box.
• Inspect the tool carefully to make sure no breakage or damage
occurred during transit.
• If any parts are damaged or missing, please email
for assistance. Do not operate this tool until
the missing or damaged parts are replaced. Failure to do so could
result in a personal injury.
• Whilst every effort has been made to ensure accuracy of information
contained within this manual, the Tacwise policy is one of
continuous improvement to our products and as such
we reserve the right to change the product specification without
prior notice.
General Safety Instructions
Important.
Tacwise recommends that this power tool should not
be modified or used for any application other than that for which it
was designed. Any such alteration or modification is misuse and could
result in a hazardous condition leading to a personal injury. If you are
unsure of its relative applications do not hesitate to contact us and we
will advise you.
Work Area
•
Keep your work area clean and well lit.
Cluttered benches and
dark areas invite accidents.
•
Keep children and pets away.
All visitors should be kept a safe
distance from work area.
•
Secure work.
Use clamps or a vice to hold work. This frees both
hands to operate the power tool.
Safety Warnings & Cautions
•
Never use oxygen combustible gases, bottled gases or high
pressure compressed gas as a power source for this tool.
The tool may explode and cause serious injury.
•
Outdoor extension cords.
When air compressor is used outdoors,
use only rounded jacket extension cords intended for outside
use. See manufacturer’s manual for the AWG required for the
compressor’s amperage draw.
•
Pay attention to air hose and their connections.
Don’t trip over
hoses. Make sure all connections are tight.
•
Use the correct air connector.
The connector on the tool must
not hold pressure when the air supply is disconnected. If the
wrong fitting is used, the tool can be charged with air after being
disconnected and still be able to drive a fastener.
•
When connecting the air.
The tool may possibly fire the fasteners
as soon as you plug it in to the air hose. Therefore, remove all the
fasteners before connecting to the air.
• Do not depress the trigger when loading.
•
If the fasteners are jammed.
Disconnect the tool from the air and
remove the jammed fasteners.
•
Stay alert.
Always watch what you are doing and use common
sense. Do not operate a power tool when you are tired or under the
influence of medication, alcohol or drugs.
•
Wear proper clothing.
Do not wear loose clothing or jewellery that
can catch in moving parts. Non-slip footwear is recommended.
Contain long hair and roll long sleeves above
the elbow.
•
Do not over reach or use on unstable surfaces.
Keep proper
footing and balance at all times.
•
Use safety equipment.
Dust mask, non-skid safety shoes, hard
hat, or hearing protection must be used for appropriate conditions.
Wear CE approved safety goggles at all times. Normal spectacles
only have impact resistant lenses; they are NOT safety glasses.
•
DO NOT use on hard surfaces
such as rock, concrete, masonry,
bricks or steel. Personal injury or damage to the power tool
could result.
•
Stored power tools.
When not in use, all power tools should be
stored in a dry, locked cupboard, out of the reach of children and
other untrained persons.
•
Recommended accessories.
Use only accessories that are
recommended by the manufacturer for your model. Accessories that
may be suitable for one tool may create a risk of injury when used
on another tool.
•
Beware of hidden danger.
Always make sure there is no danger of
hitting any hidden power cables, water or gas pipes.
•
Always assume that the tool is loaded with fasteners.
Handling
the tool without care could result in an unexpected firing of
fasteners and lead to personal injury.
•
Do not activate the power tool unless it is in contact with the
work piece.
Serious injury can result if you depress the
safety lock pin on nose/contact trip with your fingers, or by improper
operation.
•
Never point any power tool at yourself or at any other person.
While working, hold the tool in such a way that no injuries can be
caused to the head or to the body in the event of possible recoil.
•
Do not drive fasteners on top of other fasteners.
Air tool operator manual_FCN55V.indd 6
Air tool operator manual_FCN55V.indd 6
20/10/2020 15:36
20/10/2020 15:36
