Tacmina SXDA User Manual Download Page 5

– 3 –

2 Checking the Product

When unpacking, please confirm the following points:
(1) Is the enclosed product the same model you ordered?
(2) Do the details on the pump nameplate match your order?
(3) Are all the accessories present and correct?

Please refer to the accessory list in Section 2-1, below.

(4) Was the pump damaged due to vibration or shock during transportation?
(5) Are there any loose or disconnected screws?
All TACMINA products are carefully checked prior to shipment.  If, however, you find a defect,
please contact TACMINA direct or your local agent.

2-1

Accessory List

Part name

Hose type

Flange type

Union type

Hose

4m

Strainer

1 set

Anti-siphon check valve

1

Pump installation bolts / nuts

4 sets

4 sets

4 sets

Operation manual

1

1

1

1) A pump stand and pump cover are optionally available.
2) The strainer and the anti-siphon check valve are not provided with the high-viscosity models.
3) The quantities in the above chart refer to the case of simplex and standard duplex (1-box

type) models.

4) In the case of a duplex (2-box type), triplex and other models, multiply the installation

quantity by the number of pump heads. (excluding the operation manual)

5) The pump installation bolts / nuts are not provided with SYD(W)A types.

•  Accessories Exclusively for the W-Type Models

Buffer solution syringe

1 pc.

31
61
12

50mL

22
32

Glycerin

62
82

100mL

13
23
33

200mL

43

1) The quantities in the above chart are for simplex models.
2) In the case of duplex and other models, multiply the quantity by the number of pump

heads.

SXDA data̲p01-p21

Adobe PageMaker 6.0J/PPC

Summary of Contents for SXDA











Reviews: