TACKLIFE TJS01A, User Manual

Page: 2 / 10

DESCRIPTION OF THE SYMBOLS
The use of symbols in this manual is intended to draw your attention to possible risks. The safety
symbols and the explanations that accompany them must be fully understood.
GENERAL SAFETY WARNINGS FOR THE TOOL
1-
a)
b)
2-
a)
b)
c)
d)
e)
3-
a)
b)
c)
d)
e)
INTENDED USE
The machine is intended for making separating cuts and cut-outs in wood, plastic, metal, ceramic plates
and rubber while resting firmly on the work piece. It is suitable for straight and curved cuts with mitre
angles to 45°. The saw blade recommendations are to be observed.
Class II symbol: this machine is designed with double insulation. It is not necessary to connect it
to an earthed power socket.
WARNING. Read all safety warnings and instructions.
Failing to follow the warnings and instructions can result in electric shock, fire and/or serious
injury.
This symbol indicates the requirement of wearing ear protection, eye protection, respirator
and gloves when using the product.
This symbol indicates the maximum cutting depth in the Steel (8 mm). For your
security, this value must not be exceeded. This maximum value may be reduced
depending on the type of steel
This symbol indicates the maximum cutting depth in the wood (80 mm). For your
security, this value must not be exceeded. This maximum value may be reduced
depending on the density of wood.
Safety of the work area
Keep the work area clean and well lit. Cluttered and dark areas invite accidents.
Keep children and bystanders away while operating the tool.
Electrical safety
The electric tool plugs must match the outlet. Never modify the plug in any way. Do not use adapters
with earthed (grounded) tools. Unmodified plugs and matching outlets will reduce the risk of electric
shock.
Avoid any body contact with earthed or grounded surfaces such as pipes, radiators, cookers and
refrigerators.
Do not expose tools to rain or wet conditions.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the tool. Keep the cord
away from heat, lubricants, edges and moving parts.
When using a tool outside, use an extension cable suitable for outside use.
Use and maintenance of the tool
Do not force the tool. Use the correct tool for your application. The correct tool will do the work better
and safer in the conditions for which it was manufactured.
Disconnect the power cord before any adjustment, changing an accessory or before storing the tool.
Keep idle tools out of the reach of children and do not allow persons unfamiliar with the tool or these
instructions to operate it.
Maintain the tool. Check that there is no misalignment or obstruction of the moving parts, broken
parts or any other condition that could affect the operation of the tool. In the event of damage, have
the tool repaired before using it.
Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely
to bind and are easier to control.
TECHNICAL SPECIFICATIONS
LIST OF MAIN PART
OPERATON
Before use
Before making assembly, changing and adjustment for any accessory, disconnect the tool from the
mains supply to avoid any unintentional starting.
Please always check the mains supply voltage before use! It must correspond with the rating label on
the appliance.
Remove any packing material and loose parts from unit.
Check the accessories before use. It should be fit with the machine and your purpose.
Inserting Blade
-
-
-
-
Blade are hot after use. Don’t touch blade teeth by hand! Please always use protective gloves to remove
the blade.
WARNING
When removing the blade, it may jump away from holder. Please always hold the tip of blade and keep
it away from face.
Caution!
“T” shape blade only
Please always make sure the teeth pointing forwards, if the blade assembled in wrong direction, it may
cause serious injury.
Accessories can be hot after use. Don’t touch the tip of accessory by hand! Please always use protec-
tive gloves to remove the accessory.
Parallel guide
The sawing distance can be set with the parallel guide. Steps are as following:
Insert a saw blade into the blade holder and clamp it.
Loosen the screws and insert the parallel guide into the intended hole.
Move the parallel guide until the distance between the tips of blade and edge of work piece corresponds
with the required size.
Tighten the butterfly nuts by hand.
On/Off switch
The machine can only be started by pressing the on/off switch first. Press rear part of the switch to
prevent any unintentional operation.
The On/Off switch can be locked in ON position for continuous grinding by pressing down the front part
of the switch
Keep the switch on before the machine reaches the working piece.
Before putting the jig saw down, please make sure it has been stopped completely.
While working, please always hold the machine tightly at the grip area.
Caution!
Never stop the blade by apply exerting pressure on the side of the blade.
If the machine will operated with vacuum cleaner, please turn on the vacuum cleaner first before use.
Speed control knob
The speed control knob can adjust the running speed from low to high. The bigger the number, the
higher the speed.
Please follow steps below :
1.
2.
Pendulum Adjustment knob
The Pendulum Adjustment knob has 4 settings. It can be used to control the distance and the quality of
the cut according to the type of material.
Use a lower pendulum setting if you want to get better cutting quality. Setting 0 is selected for metal
plates, sheets or splinter-sensitive material Setting 1 is selected for plastic
Setting 2 is selected for hard wood Setting 3 is selected for soft wood
Adjusting the base plate
The base plate can be adjusted in positions: 0°, ± 15°, ± 30° and ± 45°.
-
-
-
-
Caution!
Unstable base plate may cause serious injury for user. Please check carefully after each adjustment.
Dust suction
To assembly the vacuum cleaner, please follow below steps:
-
-
WARNING
When sawing metal, sparks can be generated; do not use vacuum cleaner and keep other persons and
combustible material away from work area.
Application advice
For cutting a hole in a workpiece, please drill a hole by 12 mm drill first and then start the working from
this point.
Do not use the saw with a cracked, blunt or damaged blade.
Do not attempt to cut objects thicker than the maximum cutting depth of the blade or when there is not
enough space under the object for the blade.
MAINTENANCE
Keep the ventilation openings clear and clean the product regularly.
If accidence occurs during use, switch off the supply and disconnect the plug. Inspect and repair the tool
before using it again.
Repair of the tool must only be carried out by a qualified repair technician.
Repair or maintenance by unqualified personnel can lead to a risk of injury.
Use only identical spare parts for repairing a tool. Follow the instructions in the maintenance section of
this user manual.
Caution!
If the replacement of the supply cord is necessary, this has to be done by the manufacturer or his agent
in order to avoid a safety hazard.
Care and cleaning
Clean the housing only with a damp cloth and dry thoroughly afterwards. Do not uses any solvents!
STORING
Store the machine, operating instructions and necessary accessories in the original packaging. In this
way you will always have all the information and parts ready to hand.
Pack the device well or use the original packaging in order to avoid transit damage. Always keep the
machine in dry place.
WARRANTY CERTIFICATE
Congratulations! You have made an excellent choice with the purchase of this quality product. Our
commitment to quality also includes our service.
Should you, contrary to expectations, experience defects due to material or manufacturing faults during
private use within TWO YEARS of the date of purchase we shall be liable for warranty in accordance
with statutory warranty regulations, provided that:
●
●
●
●
The warranty certificate is only valid in connection with the receipt. Please keep both in a safe place. The
warranty does not affect your statutory rights. The product is guaranteed for a period of TWO YEARS
beginning on the day of purchase. Keep your purchase receipt safe as proof of the date of purchase.
The guarantee period can only be extended for the duration of any repair required. During the warranty
period, we will, at our discretion either repair or exchange the device in accordance with warranty.
EXPLODED VIEW AND PART LIST
- 01 -