manualshive.com logo in svg

T L Audio CRIMSON C-3021, User Manual

Share
Download
T L Audio CRIMSON C-3021 User Manual Download Page 11

 

 

 
 

Outputs:

 

Electronically balanced, unbalanced compatible.   

 

 

Output impedance 47 ohms. 

  Maximum 

level 

+26dBu. 

 

 

3 pin male XLR connector. 

 

 
Unbalanced Outputs: 
 
                      

Output impedance 47 ohms. 

                       Maximum level +18dBu into 10Kohms. 
                       2 pole 0.25” jack socket. 

 
 
Frequency Response:

 

 
 

 

10Hz to 40KHz, +0, -1dB. 

 
 

Noise:

  

-82dBu (22Hz - 22KHz). 

 

 

 

 

Dynamic Range:

 

 
  108dB. 
 

 
Sidechain Insertion Points:

 

 
 

 

Unbalanced, switched 3 pin jack socket, tip = send,   

 

 

  ring 

= 

return. 

  Nominal 

level 

-2dBu. 

 

 

Output impedance 47 ohms. 

 

 

Return input impedance 10Kohms. 

 
 

Power Requirements:

 

 
 

 

Rear panel selectable for 220-240V 50Hz or 110-120V 60Hz   

  operation. 
 

 

Rear panel fuse 20mm, 1AT, 250V. 

 

 

Power consumption 30VA typical. 

 

 

Detachable 3 pin IEC  connector, mating connector and cable  

  supplied. 
 

 

Front panel On/Off switch with green LED. 

 
 

Summary of Contents for CRIMSON C-3021













Reviews:

No comments

Brands by name

Popular brands

Load more brands