T.J.M. T13 Outback Frontal Protection System Fitting Instructions Manual Download

Page: 5 / 18

FITTING INSTRUCTIONS

Product:

T13 Outback Frontal Protection System

Vehicle:

Toyota LandCruiser 200 Series 2007+

Part No.

070SB13R82A

For further information contact T.J.M. Head Office on (07) 3865 9999. Distributors Australia

wide.

File: F-1434.docx

Page 5 of 18

11/12/2013

11.

Remove (& retain) the upper bumper

support & OE fasteners (indicated).

12.

Locate the fasteners securing the

indicated plastic air-guides to the vehicle.

Remove (& retain) the air-guides & O.E.

fasteners.

13.

Trim the plastic air-guides removed in

the previous step as shown

Refer to the images on the following

page also.

14.

Re-fit the plastic air-guides to the

vehicle, using the O.E. fasteners
removed in step 12

15.

Re-fit the upper bumper support using

the OE fasteners removed in step 11.

Summary of Contents for T13 Outback Frontal Protection System



















Search results

Summary of Contents for T13 Outback Frontal Protection System

Reviews:

Related manuals for T13 Outback Frontal Protection System

Brands by name

Popular brands

T.J.M. T13 Outback Frontal Protection System, Fitting Instructions Manual

Search results

Summary of Contents for T13 Outback Frontal Protection System

Reviews:

Related manuals for T13 Outback Frontal Protection System

Brands by name

Popular brands