INPUT SECTION FEATURES:
MASTER SECTION:
(1) 1/4 Line/High Impedance Input:
This may be used as either a high impedance microphone input
or a line level device such as: tape players, CD player, effects returns or radios. It will also allow
connection from an electric guitar, bass, or keyboard. It is a 2-conductor input with an impedance of
10K ohms. Both the high and low impedance inputs may be used simultaneously.
(6) Master Volume:
This controls the overall volume level of the entire amplifier. Typical operation is
between 4 and 8.
(7) Master Reverb:
This controls the level of internal reverberation added back to the mix.
(8) Tape Volume:
This controls the level of the playback inputs (RCA jacks on rear panel).
(9) Master Low:
This controls the overall amount of bass frequencies (100 Hz). This control allows
+/- 15dB of boost or cut.
(10) Master Middle:
This controls the overall amount of middle frequencies (1K Hz). This control
/- 15dB of boost or cut.
(11) Master High:
This controls the overall amount of high frequencies (10K Hz). This control allows
+/- 15dB of boost or cut.
(12) Main Output:
A 1/4 2 conductor line output. The impedance is 1K ohm. @ -10dbv. It is used to
allow the combined signals of the entire mix to be sent out to additional amplifier (for more overall
power or to create a mirror image for a monitor amp), or for patching in external equalizers or effects
such as delays or digital processors.
(2) 3 Pin Low Impedance Microphone Input:
This input is for balanced low impedance microphones.
Phantom power (15 volts) for condenser microphones is always on and available. It has an input
impedance of 1K ohm. The connector is wired as: Pin 1 = shied; Pin 2 = positive (hot); Pin 3 = negative
(cold).
(3) Volume Control:
This is the volume control for each channel. It sends the signal to the master mix
buss. Typical operation is between 4 and 8, dependent upon the device(s) on that channel, Please
remember that it acts like a pre-amp, so if you are using a device that has a volume output control (i.e.: a
tape or CD player) you will need to do some level matching by adjusting the level controls on each unit.
(5) Reverb Control:
This is a send control to the reverb buss. It controls the amount of reverberation
added to the input signals.
(4) Tone Control:
This is the adjust the overall tone of the individual inputs. It is set at 5Khz. Since it
is a cut or boost control, (+/- 15dB) it will add or diminish presence frequencies in the sound.
Power
On
7
1
9
3
10
4
6
0
5
8
2
7
1
9
3
10
4
6
0
5
8
2
7
1
9
3
10
4
6
0
5
8
2
Tone
Reverb
1
2
3
4
Channel 1
Channel 2
Channel 3
Channel 4
Master Section
Volume
Line
Mic
7
1
9
3
10
4
6
0
5
8
2
7
1
9
3
10
4
6
0
5
8
2
7
1
9
3
10
4
6
0
5
8
2
Tone
Reverb
Volume
Line
Mic
7
1
9
3
10
4
6
0
5
8
2
7
1
9
3
10
4
6
0
5
8
2
7
1
9
3
10
4
6
0
5
8
2
Tone
Reverb
Volume
Line
Mic
7
1
9
3
10
4
6
0
5
8
2
7
1
9
3
10
4
6
0
5
8
2
7
1
9
3
10
4
6
0
5
8
2
7
1
9
3
10
4
6
0
5
8
2
7
1
9
3
10
4
6
0
5
8
2
7
1
9
3
10
4
6
0
5
8
2
7
1
9
3
10
4
6
0
5
8
2
7
1
9
3
10
4
6
0
5
8
2
7
1
9
3
10
4
6
0
5
8
2
Tone
Low
Mid
High
Reverb
Volume
Volume
Reverb
Tape
PA4080KB
Powered Mixer
Line
Main
Output
Effects
Send
Aux
Input
Foot
Switch
Mic
BACK PANEL:
(1) Power:
This switches the unit on or off. When the unit is powered up, a red LED will come on also.
(14) Aux Input:
A 1/4 2 conductor line level output. output from the effects buss. This jack is used
primarily to connect to and external effects device such as a chorus, delay, or echo.
(13) Reverb Output:
A 1/4 2 conductor line output. It is used to allow the processed signals controlled
by Reverb volume to be sent out to additional amplifier (for more overall power or to create a mirror
image for a monitor amp.)
(15) Reverb Footswitch:
A 1/4 2 conductor foot switch jack. It is used to plug in a push on push offtype
footswitch to turn the internal reverb buss on or off.
(3) External Output:
These are 2 conductor 1/4 speaker outputs. You may connect 1-8
ohm speaker cabinets. Do not go below rated minimum impedance.
(4) Tape Play (L/R):
These RAC jacks are for brining in a tape deck, CD player or other line level
source. The impedance is 10K ohms @ -10 dBv.
(5) Tape Record (L/R):
These RC jacks are for hooking up a tape deck to record from the mixer. Both
channels are summed into mono for compatibility. The signals are taken pre-master section, meaning
that they are without reverb or the master tone section, and does not include the Tape In signal. The
impedance is 1K ohms @ -10 dBv.
A
TECHNICAL SPECIFICATIONS
Maximum Power
Input Impedance
Maximum Gain
Master Equalization
Input Channel Equalization
Protection Circuit
Dimension
Weight
80 Watts
Lo-Z Mic
Hi-Z Mic
Tape Playback
Lo-Z Mic-Speaker
Hi-Z Mic-Speaker
Tape In-Speaker
High
Mid
Low
1 k Ohms
10 k Ohms
10 k Ohms
76 dB
56 dB
42 dB
+/- 15 dB @ 10 kHz
+/- 15 dB @ 1 kHz
+/- 15 dB @ 100 Hz
+/- 15 dB @ 5 kHz
2 seconds
620mm H x 500mm W x 320mm D
21.0kg
Power on Mute
External
Speaker
Power
Maximum Power Consumption
160 Watts ~ 50/60Hz
1
0
Tape
Play Rec
L
R
L
R
Min 8 ohm
Impedance
ATTENTION
RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AC230V 50/60Hz
FUSE: F1AL 250V
Serial No:
Serial No:
Caution: For continued protection against
risk of fire replace only same type and
rated fuse.
Avis: Risque de choc electrique ne pas ouvrir.
Attention: Debrancher le cordon d alimentation
avant toute intervention.
Caution: To reduce the risk of electric shock
do not remove covers. No user serviceable
parts inside.Refer servicing to qualified
personnel only.
Warning: To reduce the risk of fire or electric
shock do not expose this appliance to rain
or moisture.
Attention: Remplacer le fusible seulement par le
meme type et le meme calibre.
Made in China
3
1
2
4
5
(2) Power Socket:
The socket for connecting external power source.
