T+A PH 2000 Operating Instructions Manual Download Page 8

8

Eingangsimpedanz (MC) bzw.
Eingangskapazität (MM)

Die Einstellung erfolgt durch die Codier-Schalter 

'S1/S51'

 für

den linken und rechten Kanal. Die benötigten Daten
entnehmen Sie den Herstellerangaben des
Tonabnehmersystems. Beachten Sie bitte, dass auch das
Phono-Anschlusskabel eine Kapazität darstellt, je nach
Hersteller zwischen 50 pF und 200 pF.

Wählen Sie den Wert, der den Herstellerangaben am
nächsten liegen. Es müssen unbedingt beide Kanäle gleich
eingestellt werden. Sollten Ihnen keine Herstellerangaben
vorliegen, benutzen Sie zunächst die Werkseinstellung

MC

:

100 

Ω

MM

:

120 pF

Die Einstellung ist damit abgeschlossen. Den Deckel des
Abschirmgehäuses auflegen, das Chassis vorsichtig in das
Gehäuse zurückschieben und an alter Position mit den vier
Schrauben von unten wieder befestigen.

Input impedance (MC) and
input capacitance (MM)

The code switches 

'S1/S51'

 are used to set these values for

the left-hand and right-hand channels. The information
required for this setting should be included in the
Specification provided by the pick-up cartridge manufacturer.
Please note that the phono cable also adds its own
capacitance; this lies in the range 50 pF to 200 pF, according
to manufacturer.

Select the value which is closest to the manufacturer’s stated
figure. Be sure to select the same setting for both channels!
If you do not have the manufacturer’s Specification, start with
the factory default settings:

MC

:

100 

Ω

MM

:

120 pF

This completes the settings. Place the cover of the shield
housing in position, then carefully slide the chassis back into
the case in its original position. Fit and tighten the four
screws from the underside.

Schalterstellung

Switch position

Eingangsimpedanz (

MC

)

Input impedance (

MC

)

Eingangskapazität (

MM

)

Input capacitance (

MM

)

OFF

OFF

OFF

OFF

450 

Ω

 ... 650 

Ω

... 120 pF

OFF

OFF

OFF

ON

200 

Ω

 ... 449 

Ω

121 pF

... 140 pF

OFF

OFF

ON

OFF

130

Ω

... 199

Ω

141 pF

... 160 pF

OFF

OFF

ON

ON

85

Ω

... 129

Ω

161 pF

... 190 pF

OFF

ON

OFF

OFF

50

Ω

...

84

Ω

191 pF

... 220 pF

OFF

ON

OFF

ON

221 pF

... 240 pF

OFF

ON

ON

OFF

30

Ω

...

49

Ω

241 pF

... 260 pF

OFF

ON

ON

ON

261 pF

... 290 pF

ON

OFF

OFF

OFF

20

Ω

...

29

Ω

291 pF

... 340 pF

On

OFF

OFF

OFF

341 pF

... 360 pF

ON

OFF

ON

OFF

361 pF

... 380 pF

ON

OFF

ON

ON

381 pF

... 400 pF

ON

ON

OFF

OFF

16

Ω

...

19

Ω

401 pF

... 440 pF

ON

ON

OFF

ON

441 pF

... 460 pF

ON

ON

ON

OFF

461 pF

... 480 pF

ON

ON

ON

ON

...

15

Ω

481 pF

... 500 pF

Tabelle / Table 2

Summary of Contents for PH 2000











Reviews: