BM801A INSTRUCTION MANUAL
1. Introduction
The digital clamp meter is completely portable, 3 1/2 digits
LCD display instrument for measuring AC current, DC and
AC voltage, resistance, diode and for testing audible
continuity. It is kind of ideal facility for measurement and
monitor in electrician materials, electrical equipments and
household electric appliances etc.
2. Safety Information
This clamp meter has been designed according to
IEC61010-1
Please read this manual carefully before using the meter.
2.1 Explanation of Symbols
Warning! Important safety information is found in
the manual.
risk of high voltage and electric shock!
Double insulated.
2.2 Never exceed the protection limit values indicated in the
specifications for each range of measurement.
2.3 Check the rotary switch and make sure it is at the correct
position before measuring.
2.4 Before rotating the range selector to change functions,
disconnect test leads from the circuit under test.
2.5 Never perform resistance measurements and continuity
test on live circuits.
2.6 Exercise extreme caution when measuring live system
with voltage above 60V dc or 30V ac rms.
2.7 Keep fingers behind the barriers while measuring current.
2.8 Never touch exposed wiring, connections or live circuit
when attempting to take measurements.
2.9 Change the battery when the “
” symbol appears to
avoid incorrect data.
3.Specification
3.1 General Specification:
3.1.1 Digital display: 3 1/2 digits LCD display with
maximum reading 1999.
3.1.2 Jaw opening capability: 52mm.
3.1.3 Data hold function: When the HOLD button is pushed,
the display will keep the last reading and “DH” symbol will
appear on the LCD until pushing it again.
3.1.4 Polarity: “-” displayed for negative polarity.
3.1.5 Over-range indication: “1” figure only on the display.
3.1.5 Low battery indication: When the battery is under the
proper operation range, “
” will appear on the display.
3.1.6 Auto power off: If there is not any operation with the
keys or dials within about15 minutes, the meter will power
itself off to save battery consumption. Dial the rotary switch
to turn on the meter again.
3.1.7 Operating temperature and humidity: 0
C~40
C
，
70%RH.
3.1.8 Storage temperature and humidity: -20
C~60
C
，
80%RH.
3.1.9 Power supply: 9V battery, NEDA 1604, 6F22 or
equivalent.
3.1.10 Dimension: 248
（
L
）
88
（
W
）
45
（
H
）
mm.
3.1.11 Weight: about 360g (include battery).
3.1.12 Accessory: Test leads, Instruction Manual.
3.2 Electrical Specification:
The accuracy specification is defined as
…%reading
…count.
At 23
5
C
，
70%RH.
Funcuion
Range
Resolution
Accuracy
2A
0.001A
20A
0.01A
200A
0.1A
ACA
1000A
1A
2%
10
ACV
700V
1V
1.2%
5
DCV
1000V
1V
0.8%
2
2k
1
1.0%
2
Forward current: 1mA. Reversed voltage:
2.8V.
Buzzer sounds at less than50
. Open circuit
voltage: 2.8V, Test current: 1mA.
Voltage input impeadance
：
10M
ACA/ACV frequence range: 50~60Hz
/
Overload protection: effective value 250V
4. Operating Instruction
4.1 Front Panel Description
(1)
Transformer jaws: Pick up the AC current flowing
through the conductor.
(2)
Trigger: Press the lever to open the transformer. When
the lever is released, the jaws will close again.
(3)
Rotary switch: This switch is used to selected functions
and desired ranges as well as to turn on/off the meter.
(4)
Data-hold button: The user may hold the present reading
and keep it on the display by pressing the “Hold” button.
When the data is no longer needed, one may release the
data-hold operation by press the “Hold” button again.
(5)
LCD display
(6)
“V/
” jack: This is positive input terminal for volt and
ohms.
(7)
“COM” jack: This is negative (ground) input terminal for
all measurement modes except current.
(8)
Barrier
4.2 AC Voltage Measurement
WARNING!
Maximum Input Voltage is 700V AC/DC.
Do not attempt to take any voltage measurement that may
exceed to avoid electrical shock hazard or damage to this
meter.
(1)
Set the rotary switch at AC700V position. Connect the
red test lead to “V/
” jack and the black test to the
“COM” jack.
(2)
Connect test leads across the source or loading being
measured and read voltage value on the LCD display.