background image

 
 

uLory User Guide 

 

 

 

 

 

   

 

 

 

3

This equipment has been tested and found to comply with the limits for a Class A digital 
device,  pursuant  to  part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide 
reasonable  protection  against  harmful  interference  when  the  equipment  is  operated  in  a 
commercial environment. This equipment generates, uses, and can radiate radio frequency 
energy and, if not installed and used in accordance with the instruction manual, may cause 
harmful interference to radio communications. Operation of this equipment in a residential 
area is likely to cause harmful interference in which case the user will be required to correct 
the interference at his own expense. 
 
Caution 
THE  GRANTEE  IS  NOT  RESPONSIBLE  FOR  ANY  CHANGES  OR  MODIFICATIONS  NOT 
EXPRESSLY  APPROVED  BY  THE  PARTY  RESPONSIBLE  FOR  COMPLIANCE.  SUCH 
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. 
 
IMPORTANT NOTE : FCC RF Radiation Exposure Statement 
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled 
environment. 
This  equipment  should  be  installed  and  operated  with  a  minimum  distance  of  20 
centimeters between the radiator and your body. This transmitter must not be co-located or 
operating in conjunction with any other antenna or transmitter. 
 
This  device  complies  with  part 15  of  the  FCC  Rules.  Operation  is  subject to  the following 
two conditions: 
(1) This device may not cause harmful interference, and   
(2) this device must accept any interference received, including interference that may cause 
undesired operation. 

Summary of Contents for uLory



















Reviews: