Vers. 2013-0
wall mounted fan coil unit
15
INSTALLATION, OPERATION
AND MAINTENANCE MANUAL
OPERATION GUIDE OF REMOTE CONTROLLER
1. POWER ON/OFF
- Press POWER “ ” button will turn on the air conditioner or vice versa. When
turn on, it will operate according to the setting shown on the remote unit.
2. OPERATING MODE
- By pressing the “MODE”button, the air conditioner can be put in
fi
ve operating
mode (auto, cool, dry, fan and heat).
12. TIMER ON
- The air conditioner can be programmed to turn off in advance.
Press “ON ” button, the symbol (
On
) will appear.
Press
or
button to change the real time (1 min incremental).
Hold
or
button for 3 sec, the real time will be 10 min incremental.
Press “SET”, the symbol (
On
) will appear on display.
13. TIMER OFF
- The air conditioner can be programmed to turn on in advance.
Press “OFF ” button, the symbol OFF will appear.
Press
or
button to change the real time (1 min incremental).
Hold
or
button for 3 sec, the real time will be 10 min incremental.
Press “SET”, the symbol OFF will appear on display.
Remarks:
- When the
On
symbol display on the LCD screen, press “ON ” button,
On
symbol will blink, then press “ON ” button again to cancel the TIMER ON set-
ting. The symbol
On
will disappear on the LCD screen.
- When the OFF symbol display on the LCD screen, press “OFF ”, OFF
symbol will blink, then press “OFF ” button again to cancel the TIMER ON
setting. The symbol OFF will disappear on the LCD screen.
14. CLOCK
- To set the clock on the remote unit.
Press “ ” button, the symbol will blink.
Press
or
button to change the real time (1 min incremental). Hold
or
button for 3 sec, the real time will be 10 min incremental.
Press SET button, the symbol will disappear on the LCD screen and the new
real time clock will display to the LCD screen.
15. DISPLAY
- To set the display board ON or OFF.
Note: The (
) button can be used only in FAN, COOL, HEAT, and AUTO
mode, it can not be used in DRY mode.
5. SLEEP
- Press the “SLEEP” button, LCD on the Remote unit will show (
z
z
) symbol.
- This Sleep mode is not available under DRY, FAN and AUTO mode.
- The temperature is automatically adjusted to provide comfortable sleep.
6. SWING
- Press “SWING” button will turn on/off the sweep motor.
7. LOUVER
- Press “LOUVER” button to change the angle of louver (which is controlled by
step motor).
- If the button is pressed and released, the angle of louver is change one step
at a time.
8. SEND
- Press “SEND” button to re-transmit all parameters shown on the LCD to the
main control board.
9. LIGHT
- Hold “LIGHT” button for 3sec to control the LCD screen light ON or OFF.
10. LOCK
- Hold ( ) button for 3sec to lock or unlock the other buttons, when the symbol
display on the LCD screen, the other keys were locked.
11. SET
- Hold “SET” to set clock, timer and timer off setting.
COOLING OPERATION (COOL)
1. PRESS ON/OFF BUTTON ( )
- The air conditioner turned on with the last setting.
2. PRESS THE “MODE” BUTTON
- Press the mode key repeatedly until the ( ) appears on the LCD screen.
The symbol ( ) will lights on the display board.
3. PRESS THE TEMPERATURE BUTTON (
) TO REGULATE THE TEM-
PERATURE.
- The key with the symbols (
) allows increases of 1°C.
- The key with the symbols (
) allows decreases of 1°C.
- The display shows the set value, the temperature can be between 16°C and
30°C.
4. PRESS THE FAN BUTTON
- When the ( ) button is pressed repeatedly, the system will changed the the
fan to auto, high, med and low speed.
5. PRESS THE “SWING” AND “LOUVER” BUTTON
- When the “SWING” button is pressed, the horizontal louver is oriented conti-
nuously oscillating movements. Press again to stop.
- When the “LOUVER” button is pressed, the horizontal louver work like in illu-
stration below.
FAN
The display board in the unit will show ( ). The system will operate as FAN.
The SLEEP, TEMP
and TEMP
buttons are not used.
COOL
The display board in the unit will show ( ). The system will operate as the air
conditioner.
DRY
The display board in the unit will show ( ). The system will operate as the hu-
midi
fi
er.
HEAT
The display board in the unit will show ( ). The system will operate as the heat
pump.
AUTO
The sisplay board in the unit will show ( ) and ( ) mode at the same time. The
system will automatically switch for Cool mode, Heat mode or dead band mode
depending on the inlet water temperature.
Note: In case the unit is running in Dead band mode, it will switch to FAN
mode automatically.
3. TEMPERATURE SETTING
- The setting temperature can be set in the range of 16-30°C by pressing TEMP
or TEMP
button. The LCD on the Remote unit will show the setting
temperature.
4. FAN
- Press FAN ( ) button to the select the fan speed (High, Medium, Low or Auto
mode). The display on the Remote unit will shown the status.
COOL
AUTO
DRY
FAN
HEAT
LOW
MEDIUM
HIGH
AUTO
AUTO
Louver 1
Louver 2
Louver 3
Louver 4
Louver ON
Louver OFF
HEATING OPERATION (HEAT)
1. PRESS ON/OFF BUTTON ( )
- The air conditioner turned on with the last setting.
2. PRESS THE “MODE” BUTTON
- Press the mode key repeatedly until the ( ) appears on the LCD screen.
The symbol ( ) will lights on the display board.
3. PRESS THE TEMPERATURE BUTTON (
) TO REGULATE THE TEM-
PERATURE.
- The key with the symbols (
) allows increases of 1°C.
- The key with the symbols (
) allows decreases of 1°C.
- The display shows the set value, the temperature can be between 16°C and
30°C.
4. PRESS THE FAN BUTTON
- When the ( ) button is pressed repeatedly, the system will changed the the
fan to auto, high, med and low speed.
Auto
