background image

2

Warranty

Table 1 Qualifications

Activities

Qualifications

Storage, operation, transport, cleaning, disposal

Trained personnel (see following note)

Electrical connection, commissioning, electrical
disconnection

Electrical expert or matching qualification

Installation, disassembly

Fitter or matching qualification

Maintenance

Electrical expert or matching
qualification

Fitter or matching
qualification

Repair

Electrical expert or matching
qualification

Fitter or matching
qualification

Smoke extraction fans and EX fans only by agreement with
Systemair.

Note:

The operator is responsible for ensuring that personnel are instructed and have understood the contents of
the operating instructions. If something is unclear, please contact Systemair or its representative.

2.2

Personal protective equipment

Wear protective equipment during all work in the vicinity of the fan.

• protective working clothes

• protective working shoes

• protective working gloves

• helmet

• goggles

• hearing protection

2.3

5 rules of electrical safety

1. Disconnect (disconnection of

the electrical system from
live components at all
terminals)

2. Prevent reactivation

3. Test absence of voltage

4. Ground and short-circuit

5. Cover or restrict adjacent live parts

3

Warranty

For the assertion of warranty claims, the products must be correctly connected and operated, and used in accordance
with the data sheets. Further prerequisites are a completed maintenance plan with no gaps and a commissioning re-
port. Systemair will require these in the case of a warranty claim. The commissioning report is a component of this
document. The maintenance plan must be created by the operator, see section 12.2

Maintenance

, page 12.

4

Delivery, transport, storage

Safety information

Warning: Risk from rotating fan blades

Prevent access by unauthorised persons by safety personnel or access protection.

Warning: Suspended loads

Do not walk under suspended loads.

Make sure that there is nobody under a suspended load.

Delivery

Each fan leaves our plant in an electrically and mechanically proper condition. We recommend transporting the fan to
the installation site in the original packaging.

Checking delivery

Check the packaging and the fan for transport damage. Any findings should be noted on the cargo manifest.

Check completeness of the delivery.

| 002

Summary of Contents for DVP 200DD2-4





















Reviews: