background image

2

Safety

2.1

Safety definitions

Warnings, cautions and notes are used to point out specially
important parts of the manual.

Warning

If you do not obey these instructions,
there is a risk of death or injury.

Caution

If you do not obey these instructions,
there is a risk of damage to the product,
other materials or the adjacent area.

Note:

Information that is necessary in a given situation.

2.2

Safety instructions

Warning

Read the warning instructions that follow
before you do work on the product.

• Read this manual and make sure that you understand the

instructions before you do work on the product.

• Obey local conditions and laws.

• The ventilation contractor and the operator are responsi-

ble for correct installation and intended use.

• Keep this manual at the location of the product.

• Do not install or operate the product if it is defective.

• Do not remove or disconnect safety devices.

• Make sure that you can read all warning signs and labels

on the product when it is installed. Replace labels that
have damage.

• Only permit approved personnel to work on the product

and to be in the adjacent area during all work on the
product.

• Make sure that you know how to stop the product quickly

in an emergency.

• Use applicable safety devices and personal protective

equipment during all work on the product.

• Before you do work on the product, stop the product and

wait until the fan impeller stops. Make sure that there is no
voltage on the motor terminals.

• If the maintenance is not correctly and regularly done,

there is risk of injury and damage to the product.

• Only do the maintenance as given in this manual. Speak

to Systemair technical support if other servicing is
necessary.

• Always use spare parts from Systemair.

• Sound levels exceeding 70 dB(A) may occur depending

on model and size. Visit www.systemair.com for more de-
tailed information about your product.

• The product is not to be used by persons, including chil-

dren, with reduced physical, sensory or mental capabil-
ities, or lack of experience and knowledge, unless they
have been given supervision or instruction.

• Do not allow children to play with the device.

2.3

Personal protective
equipment

Use personal protective equipment during all work on the
product.

• Approved eye protection

• Approved protective helmet

• Approved hearing protection

• Approved protective gloves

• Approved protective shoes

• Approved work clothing

3

Summary of Contents for AxZent 400























Reviews: