System Sensor ExitPoint PF24V Installation And Maintenance Instructions Download Page 4

The directional sounder will not work without power. The directional sounder gets its 
power from the fire/security panel monitoring the alarm system. If power is cut off for 
any reason, the directional sounder will not provide the desired audio warning.

The directional sounder may not be heard.

 The directional sounder may not be 

heard if it is placed on a different floor from the person in hazard or if placed too far 

away to be heard over the ambient noise such as traffic, air conditioners, machinery 

or music appliances that may prevent alert persons from hearing the sounder. The 

Sounder may not be heard by persons who are hearing impaired.

 

WARNING

 

THE LIMITATIONS OF DIRECTIONAL SOUNDERS

System Sensor warrants its enclosed product to be free from defects in materials and 
workmanship under normal use and service for a period of three years from date of 
manufacture. System Sensor makes no other express warranty for the enclosed product. 
No agent, representative, dealer, or employee of the Company has the authority to in-
crease or alter the obligations or limitations of this Warranty. The Company’s obligation 
of this Warranty shall be limited to the replacement of any part of the product which is 
found to be defective in materials or workmanship under normal use and service during 
the three year period commencing with the date of manufacture. After phoning System 
Sensor’s toll free number 800-SENSOR2 (736-7672) for a Return Authorization number, 
send defective units postage prepaid to: Honeywell, 12220 Rojas Drive, Suite 700, El Paso 

FCC STATEMENT

NOTE: Directional Sounder has been tested and found to comply with the limits for a 
Class A digital device pursuant to part 15 of the FCC Rules. These limits are designed 
to provide reasonable protection against harmful interference when the equipment is 
operated in a commercial environment. This equipment generates, uses, and can radiate 
radio frequency energy and, if not installed and used in accordance with the instruction 

manual, may cause harmful interference to radio communications. Operation of this 
equipment in a residential area is likely to cause harmful interference in which case the 
user will be required to correct the interference at his own expense. This Class B Digital 
Apparatus complies with Canadian ICES-003.

THREE-YEAR LIMITED WARRANTY

TX 79936, USA. Please include a note describing the malfunction and suspected cause 
of failure. The Company shall not be obligated to replace units which are found to be 
defective because of damage, unreasonable use, modifications, or alterations occurring 
after the date of manufacture. In no case shall the Company be liable for any consequen-
tial or incidental damages for breach of this or any other Warranty, expressed or implied 
whatsoever, even if the loss or damage is caused by the Company’s negligence or fault. 
Some states do not allow the exclusion or limitation of incidental or consequential dam-
ages, so the above limitation or exclusion may not apply to you. This Warranty gives you 
specific legal rights, and you may also have other rights which vary from state to state.

Please refer to insert for the Limitations of Fire Alarm Systems

  4 

I56-2961-002R 

  

©2016 System Sensor. 06-10

firealarmresources.com

Summary of Contents for ExitPoint PF24V

Page 1: ...he wire the less the voltage drop Generally for purposes of determining the wire size necessary for the system it is best to consider all of the devices as lumped on the end of the supply circuit simulates worst case Typical wire size resistance 18 AWG solid Approximately 8 ohms 1 000 ft 16 AWG solid Approximately 5 ohms 1 000 ft 14 AWG solid Approximately 3 ohms 1 000 ft 12 AWG solid Approximatel...

Page 2: ... High setting and if all three switches are on this selects the Low setting Directional Characteristics are as follows 3dBA angles 40 130 horizontal and vertical 6dBA angles 15 160 horizontal and vertical TABLE 4 POWER SETTING GUIDE DIP Switch Position 1 Setting DIP Switch Position 2 Setting DIP Switch Position 3 Setting Power Setting off off off High on off off Med High off on off Med off off on ...

Page 3: ...ut of the directional sounder These terminals can be connected to the dry relay contacts of control devices such as heat sensors or control mod ules When the input is active it will disable the sound output of the Sounder Connect the disable function as shown in Figure 5 Refer to Table 3 for func tion switch settings FIGURE 5 VDC TO NEXT DEVICE OR EOL OPTIONAL DISABLE CONTACT VDC MECHANICAL Two sc...

Page 4: ...0 Rojas Drive Suite 700 El Paso FCC STATEMENT NOTE Directional Sounder has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency en...

Reviews: