background image

D200-09-00 

I56-0058-004R 

 

 

 © 2007 System Sensor

System Sensor warrants its enclosed smoke detector to be free from defects in materials 
and workmanship under normal use and service for a period of three years from date 
of manufacture. System Sensor makes no other express warranty for this smoke detec-
tor. No agent, representative, dealer, or employee of the Company has the authority to 
increase or alter the obligations or limitations of this Warranty. The Company’s obligation 
of this Warranty shall be limited to the repair or replacement of any part of the smoke 
detector which is found to be defective in materials or workmanship under normal use 
and  service  during  the  three  year  period  commencing  with  the  date  of  manufacture. 
After phoning System Sensor’s toll free number 800-SENSOR2 (736-7672) for a Return 
Authorization  number,  send  defective  units  postage  prepaid  to:  System  Sensor,  Repair 

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must 
accept any interference received, including interference that may cause undesired operation.

NOTE:

 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 

reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential 
area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

three-Year Limited WarrantY

Department, RA #__________, 3825 Ohio Avenue, St. Charles, IL 60174. Please include a 
note describing the malfunction and suspected cause of failure. The Company shall not 
be obligated to repair or replace units which are found to be defective because of damage, 
unreasonable use, modifications, or alterations occurring after the date of manufacture. 
In no case shall the Company be liable for any consequential or incidental damages for 
breach of this or any other Warranty, expressed or implied whatsoever, even if the loss 
or damage is caused by the Company’s negligence or fault. Some states do not allow the 
exclusion or limitation of incidental or consequential damages, so the above limitation 
or exclusion may not apply to you. This Warranty gives you specific legal rights, and you 
may also have other rights which vary from state to state.

Please refer to insert for the Limitations of Fire Alarm Systems

0832

0832-CPd-0192

Summary of Contents for 7251

Page 1: ...te the communication line 5 Test the sensor s as described in the TESTING section of this manual Specifications Operating Voltage Range 15 to 32 VDC Standby Current 330µA 24 VDC one communication every 5 sec with LED blink enabled Max Alarm Current LED on 6 5 mA 24 VDC Operating Humidity Range 10 to 93 Relative Humidity noncondensing Operating Temperature Range 0 C to 38 C 32 F to 100 F U S 10 C t...

Page 2: ...r 9 Test the detector as described in TESTING 10 Reconnect disabled circuits 11 Notify the proper authorities that the system is back on line Figure 1 Wiring diagram CAUTION Do not loop wire under terminal 1 or 2 Break wire run to pro vide supervision of connection UL Listed Compatible Control Panel Laser Safety Information This smoke detector does not produce any hazardous laser radiation and is ...

Page 3: ... Test magnet position TENS ONES 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 D N T N I A P T O O T E S T M A G N E T TEST MAGNET PAINTED SURFACE MAGNET TEST MARKER LED STATUS INDICATORS PAINTED SURFACE C0170 00 Figure 4 Sensor assembly SENSOR COVER COVER REMOVAL TABS SCREEN ASSEMBLY SENSING CHAMBER ...

Page 4: ...art 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a ...

Reviews: