manualshive.com logo in svg

Syneron Candela VelaShape III, System User Manual, Page: 72 / 86

Share
Download
Syneron Candela VelaShape III System User Manual Download Page 72

Maintenance                                                                                                 

 

 PB81499EN

 

72 

Cleaning and Maintaining the VSmooth Applicator 

Caring for the VSmooth

 

applicator involves the following maintenance 

procedures before and after each treatment: 

●

 

Removing, cleaning and replacing the replaceable cover. 

●

 

Cleaning the interior of the applicator. 

●

 

Replacing the applicator's filters. 

 

Caution

 

While gently cleaning the interior of the applicator, avoid moisture and dirt 
from getting into the applicator’s filters. 

 
The replaceable cover of the VSmooth

 

applicator should be replaced according to 

the schedule printed on the new cover's box label, or sooner if one of the 
following is observed: 

●

 

Rollers appear damaged, discolored or their movement is impaired. 

●

 

Roller axis appears to wear out (color turns from silver to copper). 

Proceed as follows: 

1.

 

Turn the system off and disconnect the replaceable applicator cover by 
pressing the two spring-loaded buttons, then pull the cover straight off the 
applicator body, as shown in Figure 53. 

 

Figure 53: Removing the VSmooth Replaceable Cover 

Summary of Contents for Candela VelaShape III























































































Reviews:

No comments