SYNAPTICON SOMANET Node 1000 Hardware Manual Download Page 45

Page: 45 / 67

1.6.2 Specifications of the safety functions

1.6.2.1 System requirements

Required Firmware

v4.2.0 or higher

Supported Hardware

SOMANET Node 2000 Safety (E revision or newer) *

SOMANET Node 1000 Safety (E revision or newer)

SOMANET Node 400 Safety (E revision or newer)

* External fuse at main supply (48 VDC) is required for Node 2000 Safety dimensioned according to
driven load.

1.6.2.2 Technical specifications

Safety parameters

Safety Integration level (SIL) according to IEC
61508:2010

SIL 3

Performance Level (PL) according to ISO 13849-
1:2015

PL e cat. 3

Safe Failure Fraction (SFF)

99.99 %

Probability of dangerous failure per hour (PFH )

1.07

∙

10 /hour

Probability of dangerous failure on demand (PFD

)

9.41

∙

Common Cause Failure (CCF)

>65

Hardware Fault Tolerance (HFT)

Reaction time

10 ms

De-activation time

10 ms

Mean Time to dangerous Failure (MTTF )

3035 years (capped to 100 years)

Diagnostic coverage (DC )

99%

-10

avg

-6

avg

Hardware Manuals / SOMANET Node / SOMANET Node rev. E.1

45/67

Summary of Contents for SOMANET Node 1000




































































Search results

Summary of Contents for SOMANET Node 1000

Reviews:

Related manuals for SOMANET Node 1000

Brands by name

Popular brands

SYNAPTICON SOMANET Node 1000, Hardware Manual

Search results

Summary of Contents for SOMANET Node 1000

Reviews:

Related manuals for SOMANET Node 1000

Brands by name

Popular brands