fixture to the
NEUTRAL
input on the DIM10-100-
00.
6. Connect the
white
wire (neutral) from the LED
fixture to the electrical service white wire/
neutral.
Note: Steps 7-10 are for Class 1/2 Dimming Control
7. Connect the DIM- wire on the LED fixture to the
DIM-
input on the DIM10-100-00.
8. Connect the DIM+ wire on the LED fixture to the
DIM+
input on the DIM10-100-00.
9. Switch power on to the fixture. The light should
turn on.
Note:
When switched on, lamps should
turn on to full brightness; approximately 10 VDC
signal on the DIM+ wire using the DIM- wire as
reference.
10. Refer to the SimplySNAP User’s Manual for
information on provisioning the DIM10-100-00.
FIGURE 2 - WIRING DIAGRAM
Dimming
Below are some recommendations for successful
dimming using the DIM10-100-00. The dimming
control wires are referenced as Dim+ and Dim-. The
dimming signals have a Maximum voltage of 10V DC.
•
Use multi-strand 18 Gauge Wire for noise
immunity and current capability
•
Do not ground the dimming wire. This is a return
signal and is critical for dimming.
•
Route dimming wires away from AC lines if
possible.
•
Use connections with properly sized connectors.
•
Eliminate excess wire between fixtures. Line
length will cause voltage drop.
•
Number of fixtures that can be daisy-chained is
dependent upon the following factors: dimming
current, current requirements for LED driver,
length of wire, quality of connection, and gauge
of wire
•
Verify dimming capability via a “test bed” with
the number of actual fixtures, wire length,
connectors, and wire gauge
Regulatory Information and Certifications
RF Exposure Statement:
This equipment complies with
FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated
with minimum distance of 20cm between the radiator and your
body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Industry Canada (IC) certifications:
This digital apparatus does
not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of
the Canadian Department of Communications.
Le present appareil numerique n’emet pas de bruits
radioelectriques depassant les limites applicable aux appareils
numeriques de la class B prescrites dans le Reglement sur
le brouillage radioelectrique edicte par le ministere des
Communications du Canada.
FCC certifications and regulatory information (USA only)
FCC Part 15 Class B:
This device complies with part 15 of the
FCC rules. Operation is subject to the following two conditions:
(1) These devices may not cause harmful interference, and (2)
These devices must accept any interference received, including
interference that may cause harmful operation.
RADIO FREQUENCY INTERFERENCE (RFI) (FCC 15.105):
This
equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more
of the following measures: (1) Re-orient or relocate the receiving
antenna; (2) Increase the separation between the equipment and
the receiver; (3) Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected; (4) Consult
the dealer or an experienced radio/TV technician for help.
Declaration of Conformity (FCC 96-208 & 95-19):
Synapse
Wireless, Inc. declares that the product name “DIM10-100-00” to
which this declaration relates, meet the requirements specified
by the Federal Communications Commission as detailed in the
following specifications:
• Part 15, Subpart B, for Class B equipment
• FCC 96-208 as it applies to Class B personal computers and
peripherals
• This product has been tested at an External Test Laboratory
certified per FCC rules and has been found to meet the FCC, Part
15, Emission Limits. Documentation is on file and available from
Synapse Wireless, Inc.
If the FCC ID for the module inside this product enclosure is not
visible when installed inside another device, then the outside of
the device into which this product is installed must also display a
label referring to the enclosed module FCC ID. Modifications (FCC
15.21): Changes or modifications to this equipment not expressly
approved by Synapse Wireless, Inc., may void the user’s authority
to operate this equipment.
CERTIFICATIONS
Model #:
DIM10-100-00
UL File No:
E346690
Contains
FCC ID:
U9O-SM220 and
IC:
7084A-
SM220
LED Driver
DIM10-100-00
Violet
Gray
White
Black
White
Black
Dim+
Dim-
Blue
NEUTRAL
LINE
LOAD
EARTH GND
ANTENNA
1-10V
COMMON
NEUTRAL
LINE