Installation
Caution:
Be sure to turn off hot and cold water supplies before
installing or servicing faucet.
Step 1
If installing model with hose and spray, install hose
guide into hole in sink (normally the far right hole on four hole
sink). From underneath sink place washer then nut over hose
guide and secure to sink. Insert hose through hose guide and up
through middle hole from left in sink. Place gasket on base of
escutcheon. From above sink attach hose securely to nipple on
base of faucet.
Step 2
Align faucet to sink by matching underside arrow
and letter “F” on escutcheon with front of sink. Insert through
center hole of sink. Secure faucet to sink by tightening the
anchor bar (KN-23), spacer (KN-26) and nut (L-36) on the
mounting bolts from underside. (If sink surface is uneven use
putty or sealant to make proper seal under base.)
Step 3
Connect flex hoses (LN-247) to supply stops (left hose
to hot, right hose to cold). Hot supply hose is marked with tag.
Step 4
It is very important to thoroughly flush the supply
lines to prevent foreign matter, i.e. copper chips, sand, stones,
etc. from damaging the sealing surfaces of cartridge. Remove
aerator and turn valve handle on to full cold position, open cold
supply. Without closing, turn handle to full hot and open hot
supply. Let water run in hot only and cold only positions long
enough to flush supply lines thoroughly. If equipped with a hose
and spray, direct spray head into sink and activate spray. Shut
off faucet and replace aerator. Check for leaks.
Step 5
The handle limit stop can be set to limit handle turn
to the hot position. The limit mechanism is factory set to allow
full handle travel. To adjust the limit stop, turn handle to the
full hot position and lift handle to open faucet approximately
half way to obtain a smooth flow for correct initial temperature
measurement.
Step 6
If when faucet is on and in full hot position and water
is too hot, shut water off, remove plug button (KN-157), loosen
set screw (L-22) and remove handle (KN-3RB or KN-3BRB),
lift limit stop using a small flat head screw driver and rotate
clockwise to lower temperature. If water is not hot enough,
rotate counter clockwise (See Figure 1 on reverse side). After
correct temperature is achieved, reattach handle, reversing
procedure above.
Cartridge Replacement (KN-4)
Step 1
Remove plug button (KN-157), loosen set screw (L-22)
and remove handle (KN-3RB or KN-3BRB).
Step 2
Engage tabs in cartridge wrench (LN-34) with slots
in compression ring (KN-2) and use screwdriver in wrench
holes or pliers on wrench and turn counter clockwise until
compression ring engages with cap (KN-1). Continue turning
counter clockwise so that cap/ring assembly is removed from the
body (KN-11).
Step 3
Remove cartridge and o-ring seal (KN-4).
Step 4
Install new cartridge while taking care to maintain
position of the o-ring seal at the base of the cartridge. Match
posts in base of cartridge with alignment holes in adapter plate
during assembly.
Step 5
Reassemble faucet in reverse fashion. Thread cap onto
body firmly by hand. Do not use a wrench which may damage
the finish. Tighten compression ring (KN-2) finger tight using
the wrench (LN-34) then 1/4 to 1/2 turn further. Set hot water
limit stop in accordance with installation step 6 above.
Diverter replacement (KN-169)
1. Follow cartridge replacement steps 1 through 5 above.
2. Remove retaining ring (K-44) with 3/8" hex key wrench.
3. Remove diverter and o-ring (K-46).
4. Grease diverter o-ring and install into body.
5. Press diverter into o-ring and body.
6. Replace retaining ring.
Kitchen Faucet
S-23-BH Series
Installation and Service Instructions
Origins
®
Dimensions
Origins Kitchen Faucet, S-23-BH
Note:
Dimensions subject to change without notice.
10 "
257mm
1
8
20"
508mm
8"
203mm
7 "
184mm
1
4
6 "
159mm
1
4
"- 13mm
1
2
with spacer
1 "- 32mm
1
4
without spacer
"-20
UNC
spacer
1
4
5 "
133mm
1
4
8 "
222mm
3
4
10 "
276mm
7
8
"-COMP
3
8