Symbol AP-5131 Installation Manual Download Page 33

Basic AP-5131 Configuration

29

8.

Enable the radio(s) using the 

Radio Enable 

checkbox(es). If using a single radio model, 

enable the radio, then select either 802.11a (5 GHz) or 802.11b/g (2.4 GHz) from the 

RF Band 

of Operation

 field. Only one RF band option at a time is permissible in a single-radio model. 

If using a dual-radio AP-5131, the user can enable both RF bands.

9.

Select the 

WLAN #1

 tab (WLANs 1 - 4 are available within the Quick Setup screen) to define 

its ESSID security scheme for basic operation.

a. Enter the

 Extended Services Set Identification (ESSID) 

and name associated with the 

WLAN. 

b. Use the 

Available On 

checkboxes to define whether the target WLAN is operating over 

the 802.11a or 802.11b/g radio. Ensure the radio selected has been enabled (see step 8).

c. Even an AP-5131 configured with minimal values must protect its data against theft and 

corruption. A security policy should be configured for WLAN1 as part of the basic 
configuration outlined in this guide. A security policy can be configured for the WLAN 
from within the Quick Setup screen. Policies can be defined over time and saved to be 
used as needed as the AP-5131’s security requirements change. Symbol recommends 
you familiarize yourself with the security options available on the AP-5131 before 
defining a security policy. Refer to 

Configuring Basic AP-5131 Security on page -30

.

10. Click 

Apply 

to save any changes to the AP-5131 Quick Setup screen. Navigating away from 

the screen without clicking Apply results in all changes to the screens being lost, unless you 
use the 

Un-applied Changes

 pop-up window to overwrite the current settings.

11. Click 

Undo Changes

 

(if necessary) to undo any changes made. Undo Changes reverts the 

settings displayed on the AP-5131 Quick Setup screen to the last saved configuration. 

NOTE

A maximum of 16 WLANs are configurable within the AP-5131 Wireless 
Configuration screen. The limitation of 16 WLANs exists regardless of 
whether the AP-5131 has a single or dual-radio.

Summary of Contents for AP-5131

















































Reviews: