Sym Jet Sport X R50 Page 86 Service Manual Download

Page: 86 / 181

8. "V" Type Belt Drive System/Kick-Starter

8-7

Install the driven pulley that has installed the belt
onto drive shaft.

Hold the clutch outer, and then tighten nut to
specified torque value.
Special tool:
Universal holder

SYM-2210100

Torque value: 3.5~4.5kgf-m

Movable Drive Face

Removal

Remove fan cover and fan.
Remove left crankcase cover.
Hold generator flywheel with universal holder, and
then remove drive face nut.
Special tool:
Universal holder

SYM-2210100

Remove drive face.

Drive belt

Clutch outer

Drive shaft

Flywheel

Nut

Clutch/driven pulley

Drive face

Nut

Universal holder

Drive face

This chapter Contents

Summary of Contents for Jet Sport X R50






















































































































































































Search results

Summary of Contents for Jet Sport X R50

Reviews:

Related manuals for Jet Sport X R50

Brands by name

Popular brands

Sym Jet Sport X R50, Service Manual

Search results

Summary of Contents for Jet Sport X R50

Reviews:

Related manuals for Jet Sport X R50

Brands by name

Popular brands