Sym Fiddle II 50 SYM Series Owner'S Manual Download Page 19

 

18

 

§

TIRE INSPECTION 

§

 

y

  Tires should be checked and inflated with the engine shut off. 

y

  If a tire’s ground contacting curve is abnormal, check it with an air pressure gauge and inflate it to 

the specified pressure. 

y

  Tires pressure must be checked with an air pressure gauge when cold. 

 
 
 
 
 
 
 
 
 
 
 
 
 

y

  Visual check tires for frontal and lateral side walls for 

crack or damage. 

y

  Visual check tires for any nails or small stones 

wedged in the tread. 

y

  Check the “tread wear indicator” condition to see if 

tread groove depth is insufficient. 

y

  A tire with a wear bar showing is worn out and should 

be replaced immediately. 

 

 

 

 
 
 
 
 

§

STEERING HANDLE FRONT SHOCK ABSORBERS INSPECTION 

§

 

y

  Perform this check with engine shut off and ignition switch key 

removed. 

y

  Visual check front shock absorbers for damage. 

y

  Operate steering handle up and down, and check front shock 

absorbers for noises due to bends. 

y

  Check the bolts and nuts of front shock absorbers with 

wrenches for tightness. 

y

  Shake steering handle up & down, left & right, and front & rear 

to check if it is loosen, has too much resistance and pulls to 
one side. 

y

  Check steering handle if it is being pulled too tight by the 

brake cables. 

y

  Take your scooter to SYM Authorized Dealer or Franchised 

Dealer for a check or adjustment if any abnormal conditions 
are found. 

PLEASE REFER TO SPECIFICATIONS FOR STANDARD TIRE PRESSURE 

 CAUTION:  

y

  Abnormal tire pressure, wear, or crack is the most important cause that results in the loss 

control of the steering handle and a punctured tire(s). 

Tread wear 
indicator

Crack and 
damage

Foreign materials 
(nails or small 
stones) 

Summary of Contents for Fiddle II 50 SYM Series


























Reviews: