background image

 

5

 

5. DRIVING 

Ÿ

 

Keep the related parts of your body such as arms, palms, lumbar, and toes relax and ride 
with the most comfortable posture in order to be able to react quickly whenever it is 
necessary. 

Ÿ

  Rider’

s posture will greatly affect riding safety.  Always keep your body’

s gravity in the center of 

the saddle, if your body’

s gravity is on the rear part of saddle, the front wheel load will be reduced, 

and this will cause the steering handle shaking.  It is dangerous to ride a scooter with an 
unstable handle. 

Ÿ

  It will be much easier to make a turn if rider inclines his body inward when turning.  On the other 

hand, the rider will feel unstable if his body and the scooter do not incline. 

Ÿ

  The scooter is hard to control on a bumpy, unleveled, unpaved road, try to know the road 

conditions in advance, slow down and use your shoulder’

s force to control the handle. 

Ÿ

  Suggestion: Do not load objects on the front pedals unnecessarily, to avoid affecting the riding 

safety and the operation of steering handle. 

 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

6. USE GENUINE SPARE PARTS

 

In order to maintain the scooter’

s best performance, each part’

s quality, material, and machined 

precision must conform with the design requirements.  

“SYM Genuine Spare Parts”

 were made 

from the same high quality materials used for the original scooter.  No parts would be sold to the 
market until they could meet the designed specifications through sophisticated engineering and 
stringent quality control.  Therefore, it is necessary to purchase 

“SYM Genuine Spare Parts”

 from 

“SYM Authorized Dealers or

 

Franchised Dealers”

 when replacing spare parts.  If you buy cheap, 

or fake substitute parts from the market, no guarantee can be provided either for the quality or 
durability.  Also, it may result in unexpected troubles and lower the scooter’

s performance. 

 

Ÿ

  Always use 

SYM Genuine Spare Parts

 to keep your scooters pure blood and to ensure its long 

service life. 

 CAUTION: 

The rider’

s feeling on the handle is slightly different with a load or without a load.   

Overload may cause the handle to swing and affects the riding safety.   
Therefore, do not overload your scooter. 

 CAUTION: 

Ÿ

  Do not place flammable materials such as rags between the body side cover and engine to 

avoid components damaging by fire. 

Ÿ

  Do not load objects on areas not specified for loading to avoid damage. 

SUGGESTION 

To maximize the motorcycle’

s performance and prolong its service life: 

The first month or first 1000km is the wear- in period for the engine and components. 
Avoid rapid acceleration, and keep the speed below 60km/hr. 

http://www.motorcycle.in.th

Summary of Contents for AD12W1-6

























Reviews: