2
After completely reading instructions, confirm that all controls on stove are in the
OFF position. Plug the unit into a 15 amp, 120 volt outlet.
OPERATION BY CONTROL PANEL:
Controls and switches are located on front panel inside the glass door.
FLAME:
Press this button into the “I” position for main power and flame effect.
The indicator light will turn on.
HEATING:
For low heat function – press this switch while the flame switch is in the
“I” position for low heat. The indicator light will turn on.
TURBO:
For high heat function - press this switch while the heating and flame switch
are in the “I” position for high heat. The indicator light will turn on.
THERMOSTAT:
To adjust the temperature to your individual requirements. Turn the
thermostat dial to the right (clockwise) to increase the desired temperature and to
the left for lower temperature. This thermostat control dial can only be used while
the flame switch and heating/turbo switches are in the “I” position. When the heater
reaches the desired temperature, the heater and heATINg/TuRBO indicator light will
turn off but the fan will continue to operate. Adjust this knob to restart the heater.
FLAME INTENSITY:
Turn the dimmer dial clockwise or counter clockwise to get the
desired flame intensity. The dimmer switch can only be used when the flame switch
is in the “I” position.
NOTE:
When the FLAMe switch is turned to the OFF position, all other heater
functions will stop even though the switches may be in the “I” position.
OPERATION BY REMOTE CONTROL HANdSET:
POWER ON:
Press this button to turn on the unit while the “FLAMe” or “heATINg”
or “TuRBO” switches are in the “I” position. The unit will then operate according to
the function(s) selected in the control panel.
POWER OFF:
Press this button to turn off the unit. All functions will be turned off.
If you need to change the function of the unit, press the switch button(s) on the
control panel for the desired function(s).
THERMOSTAT CONTROL
The heat output is controlled by the thermostat, according to the room temperature.
Set the thermostat dial clockwise to the maximum position initially. When the room
is warm enough, reduce the setting by slowly turning the thermostat dial counter
clockwise until the heater just clicks off. This will then maintain the room temperature
at the desired level.
CAUTION:
IF YOu uSe ThIS heATeR IN CONJuNCTION WITh A TheRMAL
CONTROL, A PROgRAMMABLe CONTROLLeR, A TIMeR OR ANY OTheR DeVICe ThAT
SWITCheS ON The heATeR AuTOMATICALLY, ReMeMBeR TO OBSeRVe ALL SAFeTY
WARNINgS AT ALL TIMeS.
The STOVe heATeR hAS A SAFeTY OVeRheAT PROTeCTION. IF The OVeRheAT
PROTeCTION TRIPS, TuRN OFF ALL The SWITCheS AND uNPLug The POWeR
CORD FROM The ReCePTACLe. IT ShOuLD ReSeT AuTOMATICALLY AFTeR 5
MINuTeS.
warNiNg: discoNNEct PowEr aNd uNPlug tHE PowEr cord bEforE
attEMPtiNg aNy MaiNtENaNcE or clEaNiNg to rEducE tHE risk of
firE, ElEctric sHock or PErsoNal iNJury. tHE bulb(s) iN your uNit
caN bEcoME ExtrEMEly Hot. allow at lEast 10 MiNutEs bEtwEEN
turNiNg off tHE uNit aNd rEMoviNg tHE ligHt bulbs to avoid
accidENtal burNiNg of tHE skiN.
FLAME EFFECT
The fire effect is created with the use of a 40 watt B-10 candelabra light bulb with
an e12 (small) socket base. The light bulb will have to be replaced from time to time
when they burn out.
During normal operation, the stove heater will always give you simulated flame
function. If the intensity of flame suddenly increases, it means that the light bulb is
going to burn out.
Replace the light bulb immediately, according to the instructions. Do not operate the
stove heater when the light bulb burns out or without the light bulb.
CHANGING THE LIGHT BULB
unplug the unit and wait until it is cool before any maintenance.
STeP 1: Open the door of unit with handle.
STeP 2: Loosen the 2 screws at the front of the log set inside the stove. Carefully lift
the logset up far enough to access the light bulb. You will find 1 x 40W type
B-10 candelabra light bulb with e-12 socket base at the bottom.
STeP 3: Replace the burned out light bulb using a new 40 watt type B-10 candelabra
light bulb.
STeP 4: Reinstall the logset.
STeP 5: Plug in the unit.
REMOTE CONTROL BATTERY REPLACEMENT
Replace with a CR2025 battery. Refer to the back of remote control handset for
replacement method.