Swyx SwyxPhone L6 series User Documentation Download Page 178

Page: 178 / 206

SwyxPhone L66 Configuration

Configuring Speed Dials

176

The current function of the key is displayed. If the key is not yet
assigned, this message appears.

Choose "Modify" and press the "OK" button.



The following will appear:

Choose "Number" and press the "OK" button.

You can select a number from the phonebook or enter one
manually using the keypad:

Feature dialogue

S02: unassigned

Modify

Back

Feature dialogue

S02: Modify

Phone number

Successive dial = off

Dial immediately = on

Intercom = off

Back

The option “Dial immediately” must be activated and “Successive dial”
deactivated to use a Speed Dial.

Confirm your entry with “OK”.



The Speed Dial has been assigned a number. You can configure
another function key, or leave the configuration menu.

16.7.1 “Intercom”

Intercom connection allows you to directly speak to an internal sub-
scriber, who allows his status to be signaled to you, i.e. without him hav-
ing to pick up the call. If you press the Speed Dial on which the Intercom

connection is activated, the corresponding number will be dialled and an

intercom signal is produced for the called subscriber. The telephone or
SwyxIt! then immediately activates the line and the speaker. You can

begin your intercom connection to this subscriber.
If the called subscriber lifts the handset, you can continue the call as a
normal telephone call.

Feature dialogue

S02: Phone number

Phonebook

Enter manually

Back

Intercom connection is only possible between the internal subscribers if
you are mutually signaled the current status ("Available”/“Speaking").

If the subscriber called is currently on the phone, you cannot begin an

intercom connection.

Summary of Contents for SwyxPhone L6 series















































































































































































































Search results

Summary of Contents for SwyxPhone L6 series

Reviews:

Related manuals for SwyxPhone L6 series

Brands by name

Popular brands

Swyx SwyxPhone L6 series, User Documentation

Search results

Summary of Contents for SwyxPhone L6 series

Reviews:

Related manuals for SwyxPhone L6 series

Brands by name

Popular brands