Usage
1. Power the light
S-2041 is 6-17V voltage input and offers various power supply methods.
● By special slim battery S-8040 (Optional purchase)
①
Make sure there’s no power lead connected into DC-IN socket and the light is
switched off (turn the switch to “
〇
”).
②
Press and slip off the protection cover. See Fig 3
③
Align a fully charged S-8040 battery to the DV mount slot to same side, and
press tightly in. Slide the battery downward to snap together. See Fig 4
● By various standard DV camera batteries
①
Press and slip off the protection cover. See Fig 3
②
Align the S-7004 series battery plate to the DV mount slot to same side, and
press tightly in. Then slide the S-7004 downward to snap together. See Fig 5-
①
③
Fix the DV mount with two screws.
④
Make sure the light is switched off (turn the switch to “
〇
”). Mount a fully
charged battery to the S-7004 mount. Fig 5-
②
Remark: After use, please fix on the protection cover.
There’re the following types of S-7004 for choice: (Optional Purchase)
Model
Compatible battery type
Recommended SWIT battery
S-7004F
SONY NP-F770/970
S-8972, S-8970, S-8770
S-7004P
Panasonic CGA-D54S/D28S
S-8D62, S-8D54, S-8D28
S-7004J
JVC BN-V428U
S-8428
S-7004C
Canon BP-930/945
S-8945, S-8845
S-7004U
SONY BP-U60/30
S-8U62
S-7004E
Canon DSLR LP-E6
S-8PE6
S-7004B Panasonic VW-VBG6
S-8BG6
S-7004V
JVC BN-VF823
S-8823
S-7004I
JVC SSL-JVC50
S-8I50
● By DC input cable
①
Make sure the light is switched off (turn the switch to “
〇
”). Plug the pole end of
S-7104 into the DC-IN socket.
②
Plug the D-tap end of S-7104 to the camera auxiliary power tap or the battery’s
D-tap output socket. See Fig 6.
③
For third-party DC cables, please make sure the DC connector is 5.5/2.1mm
pole and input voltage should be 6-17V; and inner: positive, Outer: negative.
2. Fix the LED light to the camera
● By screw mount (Fig. 8)
The S-2041 can be directly installed on 1/4” thread handle.
● By Cold shoe (Fig. 9-11)
①
Unscrew the 4 screws and take down the 1/4” bolt base from the light.
②
Install the supplied cold shoe base onto the light.
③
Anticlockwise revolve the fasten knob, and loose the cold shoe slice, then
install onto the camera cold shoe slot, and fasten the knob to finish.
3. Adjust the angle of the light
:
Hold the light, and adjust the light upward or downward. See Fig 12.
4. Open barn doors and filters
:
Open the barn doors and filters to about 45°.
5. Switch on:
Turn the switch to “ I ”.
6. Adjust the illuminance
:
Adjust the illuminance from 10% to 100% by the dimmer.
7. Adjust color temperature
:
Output 5600K light by using 5600K filter; Output 3200K light by using 3200K filter
Fig 4
Release button
Screw hole
Battery
release
Fig 6
Pole plug
Fig 7
Fig 12
Adjust upward
or downward
Fig 5
Fig 8
Press and slip
to release
Fig 3
Cover
Fig 9
Fig 10
Fig 11