Usage
Packing list
1. Installation
Mount the lamp head onto a light stand, then fix it in place by
tightening the T-Handle on the mounting column. Then loosen
/tighten the handbrake locking mechanism on the yoke to
adjust the tilt of the fixture.
Tips:
Please use with safety rope when lifting lamps. See "Safety
Rope Assembly" for the assembly method of safety rope.
2. Power supply
This light support DC 11-17V（Polarity：Pin1＂－＂；Pin4＂+＂）、AC
100-240V 50/60Hz two ways of power supply， loop out is
supported when AC power is supplied，Maximum:20pcs .
3. Brightness/CCT setting and usage
This product supports two brightness/color temperature
adjustment modes: normal adjustment mode, fast adjustment
mode.Switch according to the brightness/color temperature
adjustment knob (Figure 4 ⑩/ unkind) . Users can quickly set
brightness and color temperature by combining these two
adjustment modes according to their needs.
3.1 Normal adjustment mode
1）CCT
Range：2700K-6500K，adjustment steps：50K；
2）Brightness
Range：0%-100%，adjustment steps：1%。
3.2 Fast adjustment mode
1）CCT
In this mode,these CCT can be choose quickly：2700K、
3200K，4500K，5600K，6500K；
2）Brightness
Range：0%-100%，adjustment steps：10%。
4. Communication address setting and usage
Hold the brightness adjustment knob (As shown in Figure 4 ⑩)
for about 2 seconds to enter the communication address setting
interface. The communication address setting range is 001-512.
The LCD (Figure 5 ④) blinks, indicating that the current position
is selected. Rotate the brightness adjustment knob (Figure 4 ⑩)
to set the current position and press the brightness adjustment
Knob (Figure 4 ⑩) to determine the current bit Settings and
enter the next bit Settings. When the last bit Settings are completed,
press the brightness adjustment knob (Figure 4 ⑩) or wait for
about 5 seconds to exit the communication address Settings.
5. Communication control mode setting and usage
Connect the lamps through DMX, and press the color tempera-
ture adjustment knob (FIG. 4) for about 2s to complete the
setting of the communication control mode of the lamps.
5.1 DMX Communication mode
"DMX" is displayed in the upper left corner of LCD (Fig. 5 ①),
indicating that the current communication control mode
supported by the lamp is DMX communication mode.In this
mode, the DMX signal output device is connected to the lamp
network, the communication address is set, and it can be used
normally.
A lamp occupies a total of two DMX control channels, the current
set DMX address (N) for brightness control, the current set
value of the next address (N+1) for color temperature control
For example：
DMX
communication
address
Function
Intensity 0%-100%
Color temperature 2700K-6500K
DMX
Control
address
005
006
005
5.2 Mutual mode
"CH" is displayed in the upper left corner of LCD (Figure 5 ②),
indicating that the communication control mode currently
supported by the lamp is mutual control mode.In this mode,
the target lamps are set to the same communication address
and can be used normally without distinguishing the master
and slave machines.
Note: When using the mutual control function of lamps,
do not access the OUTPUT device of DMX signal in the
network of lamps, otherwise the function can not be
used normally;
6. USB usage
The USB port is a reserved port. Please use it according to the
environment specified by the company's related products.
Otherwise, the USB port may not be used for other purposes.
No.
1
2
3
4
Item
CL-M100D
AC power cable
Safety rope
AC loop out cable（optional）
Engineering kit
X
1
X
1
X
2
Client can purchase according to requirement
