Swiss Timing OSB 14 Series Page 15 User Manual Download | Manualshive

Page: 15 / 21

background image

Swimming Starting Block / OSB 14

Version 1.4

3454.519.02

Page 11

Rotate the platform to access the lateral screws and unscrew the 4 screws (2 on each side).

Pull to remove the footrest.

To reassemble the footrest, start from this point and follow the instructions backwards.

Figure 9

– Dismantling of the footrest

«
...
13
14
15
16
17
...
»

Summary of Contents for OSB 14 Series






















Reviews:

No comments

Related manuals for OSB 14 Series

Brand: EAST OAK Pages: 11

Brand: Xpedition Archery Pages: 4

Hot Air Balloon 10 Light LED Outdoor Line Lights

Brand: John Lewis Pages: 2

Profile Area Light BW402

Brand: Landscape Forms Pages: 5

Brand: Quoizel Pages: 2

Brand: MD SPORTS Pages: 24

Patron cart Corner connector

Brand: Patton Pages: 7

Brand: Ice-Trek Pages: 2

Brand: Quoizel Pages: 2

Brand: FLYSURFER Pages: 28

Torino 8403-650

Brand: Malmbergs Pages: 3

Brand: SPORTSPOWER Pages: 16

Brand: DuraMax Pages: 81

Brand: Prince Pages: 10

Brand: Würth Pages: 10

Brand: Seville Classics Pages: 2

Brand: Zafferano Pages: 16

Brand: Heath Zenith Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands