Swisher ZT2454 Owner'S Manual Download Page 38

38

38

WARRANTY RIGHTS AND OBLIGATIONS

YOUR WARRANTY RIGHTS AND OBLIGATIONS: The California Air Resources Board and Swisher Mower, is pleased to 
explain the evaporative emission control system (EECS) on your model year 2006 and later Swisher Product.  In California, 
new Outdoor Power Equipment, must be designed, built and equipped to meet the State’s stringent anti-smog standards.  
Swisher Mower must warrant the EECS on your Power Equipment, for the period of time listed below provided there has 
been no abuse, neglect, or improper maintenance.  For model year 2006 the EECS on your mower includes the liquid fuel 
lines, fuel line connectors, and fuel line clamps.  Where a warrantable condition exists, Swisher Mower will repair at no cost 
to you.  Expenses covered under warranty include diagnosis, parts, and labor.

MANUFACTURER’S WARRANTY COVERAGE:  For a period of two years, any evaporative emission-related part included 
in the list of EECS parts for your mower is defective, the part will be repaired or replaced by Swisher Mower.

OWNER’S WARRANTY RESPONSIBILITIES: As the owner of this Power Equipment, you are responsible for performance 
of the required maintenance listed in your owner’s manual.  Swisher Mower recommends that you retain all receipts
covering maintenance on your Power Equipment, but Swisher Mower cannot deny warranty solely for the lack of receipts.  
As the Power Equipment owner, you should be aware that Swisher Mower, may deny you warranty coverage if your Power 
Equipment, or a covered part has failed due to abuse, neglect, or improper maintenance, unapproved modifications, or the 
use of parts not made or approved by the equipment manufacturer. You are responsible for presenting your Power 
Equipment to an authorized Swisher Service center as soon as the problem exists.  Warranty repairs should be completed 
in a reasonable amount of time, not to exceed 30 days.  If you have a question regarding your warranty rights and 
responsibilities, you should contact the Swisher Mower Service representative at 1-800-222-8183.

WARRANTY COMMENCEMENT DATE: The warranty period begins on the date the Power Equipment Is purchased.  

LENGTH OF COVERAGE:  This warranty shall be for a period of two (2) years from the initial date of purchase.  

WHAT IS COVERED:  Warranted parts include the Liquid fuel line, fuel line connectors, and fuel line clamps.

REPAIR OR REPLACEMENT OF PARTS:  Repair or replacement of any evaporative warranted part will be performed at 
no charge to the owner at an authorized Swisher Mower Service Center.  If you have a question regarding your warranty 
rights and responsibilities, you should contact your nearest authorized service center or call the Swisher Mower Service 
representative at 1-800-222-8183. 

WARRANTY PERIOD: Any warranted part is not scheduled for replacement as required maintenance, or which is 
scheduled only for regular inspection to the effect of “repair or replace as necessary” shall be warranted for two (2) years.  
Any warranted part that is scheduled for replacement as required maintenance shall be warranted for the period of time up 
to the first scheduled replacement point for that part. 

DIAGNOSIS: The owner shall not be charged for diagnostic labor that leads to the determination that a warranted part is 
defective if the diagnostic work is performed at an authorized Swisher Service Center.

CONSEQUENTIAL DAMAGE: Swisher Mower, may be liable for damages to other engine or equipment components 
caused by the failure of a warranted part still under warranty.

WHAT IS NOT COVERED: All failures caused by abuse, neglect, or improper maintenance is not covered. 

ADD-ON OR MODIFIED PARTS:  The use of add-on or modified parts may be grounds for disallowing a warranty claim.  
Swisher Mower is not liable to cover failures of warranted parts caused by the use of an add-on or modified part.  

HOW TO FILE A CLAIM: If you have a question regarding your warranty rights and responsibilities, you should contact your 
nearest authorized service center or call Swisher Mower Service representative at 1-800-222-8183.

Summary of Contents for ZT2454









































Reviews: