manualshive.com logo in svg

Swisher RESIDENTIAL ZTR2466BS-CA, Manual, Page: 20 / 24

Share
Download
Swisher RESIDENTIAL ZTR2466BS-CA Manual Download Page 20

栐

Ǽ

SERVICE & ADJUSTMENTS

Seat Adjustment

Swisher Response Zero Turn Mowers are equipped with a 4” range sliding seat.

Release the tension on the seat adjustment lever by pushing the grey tip lever to the left. 

SEE FEATURES section in this manual.

Using your own weight, slide the seat to the desired position.

Release the lever and be certain you feel the seat slide lock into place.

PTO Clutch Adjustment

Please visit  www.ogura-clutch.com/files/pdfIMP/PTOinstallation.pdf to view maintenance, 

adjustment and installation instructions. 

Hydro Expansion Tank Oil Levels

Swisher Response Zero Turn Mowers are equipped with two hydrostatic transmission

expansion tanks to allow for oil expansion during regular use. These are located directly
behind the seat and in front of the engine. 

Oil levels in both expansion tanks (when oil is cold or at ambient temperature) should always 

be kept at the “full cold” line. Note: Oil levels could rise above this line once the oil has been
used and has increased in temperature. Wait until oil has cooled back to the ambient
temperature before checking the oil levels. See image below for reference. 

If oil level in either tank is below the “full cold” line please remove the cap and add *oil to the

tank until it reaches the “full cold” line.

*Only use SAE 20w-50 engine oil; preferably with the following specifications:

•Viscosity Rating: 162 @ 40°C / 18.1 @100°C

•13cSt & 9cSt min @ 110°C

•API Classification: SL

Using another type of oil may void the warranty. 

20

Full Cold Line

Above 

Below

Cap

Expansion Tank

Summary of Contents for RESIDENTIAL ZTR2466BS-CA

























Reviews:

No comments