Swisher L116-245001 Owner'S Manual Download Page 2

2

In  the  event  you  have  a  claim  under  this  warranty,  you  must  return  the  product  to  an  authorized 
service  dealer.    All  transportation  charges,  damage,  or  loss  incurred  during  transportation  of  parts 
submitted for replacement or repair under this warranty shall be borne by the purchaser.  Should you 
have  any  questions  concerning  this  warranty,  please  contact  us  toll-free  at  1-800-222-8183.    The 
model number, serial number, date of purchase, and the name of the authorized Swisher dealer from 
whom you purchased the mower will be needed before any warranty claim can be processed.
THIS  WARRANTY  DOES  NOT  APPLY  TO  ANY  INCIDENTAL  OR  CONSEQUENTIAL 
DAMAGES  AND  ANY  IMPLIED  WARRANTIES  ARE  LIMITED  TO  THE  SAME  TIME 
PERIODS  STATED  HEREIN  FOR  ALL  EXPRESSED  WARRANTIES
.    Some  states  do  not 
allow the limitation of consequential damages or limitations on how long an implied warranty  may 
last, so the above limitations or exclusions may not apply to  you.  This warranty gives you specific 
legal rights and you may have other rights, which vary from state-to-state. This is a limited warranty 
as defined by the Magnuson-Moss Act of 1975. 

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is:  This product is free from defects 
in materials and workmanship for a period of  (1) year from the date of purchase by the original 
consumer purchaser.  We will repair or replace, at our discretion, parts found to be defective due to 
materials or workmanship.  This warranty is subject to the following limitations and exclusions:

TABLE OF CONTENTS

WARRANTY………………....….2
INTRODUCTION………………..3
SAFETY..……………………….3-4
PRE-OPERATING..….……..……4

OPERATION.……………………….5-7
DECALS…..………….……………….8
PARTS BREAKDOWN…………….9-13
MAINTENANCE LOG..…………..…15

1)

Engine Warranty

All engines utilized on our products have a separate warranty extended 
to them by the individual engine manufacturer. Any engine service 
difficulty is the responsibility of the engine manufacturer and in no 
way is Swisher or its agents responsible for the engine warranty. The 
Briggs & Stratton Engine Service Hot-Line is 1-800-233-3723.

2)

Commercial Use

This product is not intended for commercial use and carries no 
commercial warranty.

3)

Limitation

This warranty applies only to products which have been properly 
assembled, adjusted, and operated in accordance with the instructions 
contained within this manual. This warranty does not apply to any 
product of Swisher that has been subject to alteration, misuse, abuse, 
improper assembly or installation, shipping damage, or to normal wear 
of product.

4)

Exclusions

Excluded from this warranty are normal wear, normal adjustments, and 
normal maintenance.

Summary of Contents for L116-245001

















Reviews: