THROTTLE CALIBRATION
COMPASS CALIBRATION
Splash Drone PRO
Splash Drone PRO
INSTALLING THE MONITOR
HOW TO FLY
HOW TO LAND
Splash Drone PRO
Specification
Splash Drone & Battery & Transmitter Specification
Start motor
(Lock/Unlock I)
Lock/Unlock motor
Left stick/rise(Slow)
aircraft Tail
Right Stick
Left Stick
1
1
2
3
2
4
3
Power off aircraft. Push throttle
stick to the top position.
05
06
07
08
09
10
11
12
Up
T
urn
R
igh
t
D
own
T
ur
n
Le
ft
Forward
R
igh
t
Bac
kwa
rd
L
ef
t
Up
T
urn
R
igh
t
D
own
T
ur
n
Le
ft
Forward
R
igh
t
Bac
kwa
rd
L
ef
t
4. Remote Control throttle Joystick Calibration
5. Compass Calibration
Put the battery inside the aircraft and install in the correct position. Ensure
it is tightend firmly before starting the aircraft
1. First time using the remote control.
2. When the joystick is in middle position. but aircraft drifts to one side.
3. Remote control crash occurs.
1. First time using the aircraft
2. More than 100 km from the last calibration.
3. Crash occurs
4. If aircraft parameters have been changed.
5. When aircraft shakes or has twitching motions
1. Turn on remote control.
2. Push throttle stick up.
3. While holding the stick up, power on
drone and wait till the blue LED flash
intermittent on the drone.
3. Pull throttle stick to the lowest
position till you see the red LED flash
intermittent. NOTE: DO NOT move the
trottle stick left or right, only up and
down while doing this calibration.
3. Put aircraft in a horizontal
position and continuous rotate it in a
clockwise motion for 2 full circles till the
green LED starts flashing.
4. Turn aircraft face down;
keep the drone vertical and
continuous rotate it clockwise 2
circles till red LED starts flashing.
Quickly move SWA fully up and
down while holding the throttle
down till the Green LED starts
fast flashing
Put aircraft in horizontal position;
rotate in clockwise 2 circles till
green LED slow flashing
Turn aircraft head down.
rotation in clockwise 2
circles till green LED stops
flashing
1. Put aircraft on a stable level
surface and power on.
2. Pull Throttle stick in lowest
position. DO NOT move to sides
3. Quickly move the right stick
left and right till LED flashes Red.
Release the remote control.
1. First time using the aircraft
2. Drone is not flying stable
3. Aircraft sides lips
4. Aircraft Crash Occurs
1. Turn on remote control and
drone till you see the red led flashing
normal, then move throttle to lowest
position. NOTE: DO NOT move stick left
and right.
2. Quickly move SWA fully up and
down 6-10 times till the green LED fast
flashes continuously. Let go of the throttle
stick.
1. Place aircraft in an open area without buildings or trees, and keep 3-5
meters away from you and others
2. Power on the Control, then power on the Splash Drone and wait for GPS
signal. (wating for GPS is optional but highly recommended)
3. Pull both sticks to their lowest corners to start up the drone
4. Slowly raise throttle stick to start flying
1. Slowly pull down throttle stick until the aircraft lands on the ground
2. Please keep throttle stick in the lowest position for over 5 seconds to
allow motors to lock after landing
3. After motor stop rotating, shut down aircraft power
4. Power off Remote controller
1. Please land aircaft in an open area
2. If aircraft lands on tree or any other abnormal place, lock motors
immediately to avoid motor and ESC burnout.
3. After aircarft lands on the ground keep remote controller throttle
stick in lowest neutral position until motors stop rotating
1. Power on aircraft, it will enter a self-check test. Please make sure
there is no movement on the aircraft in this period(6-10 Seconds).
2. Aircraft satellite indications: 6 satellites - 2 red LED flashing. 7
satellite - 1 red LED flashing and over 8 satellite no red LED flashing.
We strongly recommend aircraft search over 6 satellites before starting
to fly.
3. In flying process do not stop motors for any reason.
While holding the throttle up, power on
the drone. Pull throttle joystick to the
lowest neutral position till bule LED
Throttle Calibration Process
LED Flashing
Compass Calibration Process
LED Flashing
Horizontal Position Calibration
LED Flashing
Pull left joystick to the lowest neutral position, quickly left and right move
the pitch joystick. till LED become Red. Blue and Green flashing.
e. Install Battery
6. Aircarft Horizontal Position Calibration
9. Launch(Outdoor)
Lock/Unlock II
Lock/Unlock III
Lock/Unlock IV
10. Landing(Outdoor)
Image
Calibration is needed if:
When to Calibrate
When to Calibrate
8. Prepare
7. FPV monitor
Notice:
Quick Guide
Quick Guide
Quick Guide
Quick Guide
Quick Guide
Quick Guide
Quick Guide
Quick Guide
Splash Drone
Weight (Battery & Propellers Included)
Hover Accuracy
Max Yaw Angular Velocity
Max Tilt Angle
Max Ascent / Descent Speed
Max Flight Speed
WheelBase
Flight Time
Max Take-Off Weight
Operating Temperature
Battery
Battery Type
Capacity
Charging Environment Range
Charging Time
Remote Controller
Weight
Operating Frequency
Communication Distance (Open Area)
Receiver Sensitivity (1%PER)
Working Current/Voltage
Battery
Channels
1750Kg
0. 2 m
30°
30°
4 m/s
6m/s (GPS Mode)
450mm
19 Mins ( 4500mah)
2. 5Kg
-10C°to 60C°
Lipo Battery
14. 8V 4500mah
0C°to 40C°
60minutes
390g
2405 to 2475HMZ
1. 0 KM
-105dbm
120 mA
1. 5V AA*4
8 channels
Notice:
Notice:
Defult remote controller is Mode 2. if need mode 1. (Check user manual)
