Splash Drone PRO
TURNING REMOTE ON
Splash Drone PRO
Splash Drone PRO
Splash Drone PRO
Remote Controller
Safety Guide
V1. 0
PRO
01
03
01 19
02
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
20
21
22
02
03
04
05
06
07
08
09
10
11
12
M2
USB
A1
12V
12V
A0
5V
GND
IMU
M1
GPS
POWER LED
IO CHANNELS
2. 4
GHz RECEIVER
01
02
03
04
www. swellpro. com
Distribuited by:
UrbanDrones.com
a. Check that all parts are in good condition and installed properly.
b. Ensure that remote control batteries are full
c. Calibrate Splash Drone and remote control (only during initial set-up)
a. Place SWA and SWB swith to the UP
position.
b. Power up remote control
c. A safety beeping sound will start. Move
throttle joystick down once. This will stop
the beeping sound. The remote is now
ready.
NOTE: Ignore the warning sign on the
control LED.
Insert land gear to the bottom of the Splash Drone PRO aluminum brackets
and ensure installation is firm.
1. Put aircraft on a flat level surface
2. Install the sliver nut propellers with motor marked “CCW“ . and Black nut
propellers with “ CW ” motor. ensure all propellers tighten firmly .
1. First Start:
2. Powering on remote control
3. Splash Drone PRO set up.
1. Uninstall the seal screw that comes
installed.
2. Push VTX cable(3PIN), IMU
cable(4PIN), Gimbal Roll direction
control cable M1 (3PIN) and Gimbal Pitch direction control board M2(3PIN)
through the hole and tighten seal screw fix firmly.
3. VTX. IMU. M1. M2 cable connect to the VTX module and gimbal control
board corresponding ports as labelled.
4. Gimbal board power cable connects with main board “12V Out JST”,
pitch control (green cable) connects to receiver CH5. Roll control (blue
cable) connects to receiver CH6. Ground (black cable) connects to CH5 or
CH6 ground port
1. Obey relevant regulations of the International Civil Aviation Organization
and local airspace control law and UAV management rules. Forbid flying in
any no-fly zones.
2. When flying the Splash Drone always keep it in an open area without
buildings, trees and obstacles.
3. Keep 3-5 meters away from you and others. Do not operate close to
crowds.
4. Before flight need calibrate the aircraft and Remote Controller
5. If detect abnormal operation while using the Splash Drone and/or remote
controller please stop using immediately
6. Before flight, ensure the propllers are installed in correct direction and
firmly on motor
7. Do not attempt to touch the motor until motors stop rotating .
8. If use WiFi Sport camera with aircraft. please disable WiFi function
before flight. Wifi should not be used in the area of flying.
9. If aircraft has low battery, land immediately to avoid damage.
10. Do not move aircraft for 6-10 seconds after powering on aircraft.
11.If loss of radio signal occours, aircraft will enter into Auto Return Home
mode automatically ; If signal is received again, please switch to GPS
mode control aircraft.
Forbidden flight conditions:
a. Forbid flying nearby strong radio interference activity areas.
b. Forbid flying nearby any crowds.
c. Forbid flying in extreme weather, like heavy rain, thunderstorms or
conditions causing poor visual range
d. Forbid flying around strong magnetic fields
e. Forbid flying when you are tired or affected by alcohol.
f. Forbid flying when remote controllor can not control aircraft due to any
other reasons
5. Install gimbal control board between fight controller and GPS antenna
corresponding location (Back of board installed 3M glue)
6. Install gimbal mount to the bottom of aircraft . Adjust to the correct
position and use screw to lock firmly.
7. Open dive case and connect your camera AV output port to the AV cable
from within the dive case
Suggestion Installation
3. Use screw through fixed sheave, and choose a correct position lock
firmly
4. Payload release control cable connects with the receiver at CH5 or CH6.
(CH5 controlled by remote controller VRA. CH6 by VRB)
1. Uninstall the seal screw
2. Push the payload release control cable through the hole and fix firmly
with seal screw. Use screws to fix the mechanism to the body firmly.
c. OPTIONAL: Payload Release Mechanism
a. Land Gear
d. Propellers
b. Gimbal
Gimbal
Splash Drone Quick Guide
1. Antenna
2. VRA
3. Switch A(SWA)
4. Hanger
5. Left trims
6. Left Stick
7. Left trims
8. Up Key
9. Down Key
10. Binding Key
11. LCD Display
12. Power Switch
13. Cancel Key
14. OK Key
15. Right trims
16. Right Stick
17. Right trims
18. Switch B(SWB.
19. VRB
20. Handle
21. Trainer Jack
22. Battery cover
1. Cover screw
2. Prop
3. Aircraft Nose
4. Flight Indicator LED
5. Gimbal Damper ball
6. Waterproof Gimbal
7. Land Gear
8. Seal Screw
9. Rubber Root
10. Motor
11. Prop Nut
12. Seal Cover
Gimbal
controller
board
Gimbal
controller
board
Flight
controller
Receiver
Receiver
Battery
Video transmitter
Video transmitter
Quick Guide
Quick Guide
Quick Guide
Quick Guide
