5
Ändringar förbehålles
Änderungen vorbehalten
Subject to change without notice
Valid from 02-06-12
Swedmach Logistics AB
,
www.swedmach.se
Finnögatan 1, S-582 78 LINKÖPING, SWEDEN
LW22
Tele Spare Parts:
+46-13-10 22 90
Fax:
+46-13-10 23 25
e-mail:
1. Information and General Specifications
Your pallet truck is made of high quality steel and
was designed to give you a durable, reliable
and easy to use product. For your safety and correct
operation, please carefully read this instruction before
using it.
2. To attach handle to pump unit
See figure 2 below for description.
2.1
Remove 3 bolts (20960) from the handle bracket (20849).
2.2
Set the handle (20959) on the bracket (20849), notice to allow the chain and the adjusting bolts assembly to pass
through the hole in the center of the bracket (20849) and shaft (20851).
2.3
Insert the 3 bolts (20960) through the handle into the bracket (20849), then tighten them securely.
2.4
Raise the lowering arm (20832) and insert the adjusting bolt into the front slot, keeping the adjusting nut (20451)
on the under side of the lowering arm (20832).
3. To adjust release device
On the tow bar of the pallet truck, you can find the control
handle (20957) which can be regulated in the following positions:
1. Lower position
-
handle up, the lever moves back to
the drive position when released
2. Drive position
- handle in the center position
3. Raise position
- handle down
See figure 1 to the right.
If the positions have been changed, you can adjust them according to the following step:
3.1
If the forks elevate while pumping in the
drive position
, turn the adjusting nut (20451) on the adjusting bolt or
adjusting screw (20833) clockwise until pumping action does not raise the forks and the drive position functions
properly.
3.2
If the forks descend while pumping in the
drive position
, turn the nut (20451) or adjusting screw (20833)
counter-clockwise until the forks do not lower.
3.3
If the forks do not descend when the control handle (20957) is in the
lower position,
turn the nut (20451) or
adjusting screw (20833) clockwise until raising the control handle (20957) lowers the forks. Then check the
drive
position
according to item 3.1 and 3.2 to be sure the nut (20451) or adjusting screw (20833) is in the proper position.
3.4
If the forks do not elevate while pumping in the
raise position
, turn the nut (20451) or adjusting screw (20833)
counter-clockwise until the forks evelate while pumping in the
raise position.
Then check the
lower
and
drive
position
according to item 3.1, 3.2, and 3.3.
Adjusting nut, 20451
Adjusting bolt
Bolts, 20960
Bracket, 20849
Figure 2
Figure 1
1
2
3
y
t
i
c
a
p
a
C
g
k
0
0
2
2
h
t
d
i
W
m
m
5
8
6
/
0
2
5
/
0
5
4
t
h
g
i
e
W
g
k
0
1
1
-
2
6
h
t
g
n
e
l
k
r
o
F
m
m
0
5
3
2
-
0
0
6
t
h
g
i
e
h
k
r
o
f
.
x
a
M
/.
n
i
M
m
m
0
0
2
-
5
8
/
0
9
1
-
5
7
