SwedeSolutions Litecam P2 Installation Manual Download Page 27 | Manualshive

Page: 27 / 28

SwedeSolutions Litecam P2 Installation Manual Download Page 27

Installation manual

Litecam P2

QUICK REFERENCE/START GUIDE

CFE Plus (WiFi)

© 2020 SwedeSolutions the Netherlands - [email protected] - www.swedesolutions.com

Instruction# 1669

Version# 0.8

Part# -

EAN# SE-12

Author: KW

27/30

FOR ALL MODELS AGAIN:

If you want to see parking lines, you can cut the

GREEN Wire.

But note before you do so; as

in the original Volvo camera, you cannot expect the lines to match the exact straight, simply
because the camera is not centered totally!) We suggest you work without the parking lines.

You’ll also find a

WHITE

wire-loop at the camera side. Make sure this loop is CUT to make the

image on the RTI screen MIRROR. (I.e. left on the RTI screen = left in reality!)

So now put the ignition in position 2, and put car in reverse (with handbrake on please!) and
look at the image of the camera on the RTi screen. Now adjust the camera as you want and
decide which position is the one you like.

END OF INSTRUCTION

«
...
25
26
27
28
»

Summary of Contents for Litecam P2





























Reviews:

No comments