Swann ULAD-1913 Manual Download Page 14

Product Care and Cleaning

Swanstone solid surface products are stain and abrasion
resistant; however, the finish requires reasonable care.

Abrasive cleaners, such as Comet or Ajax, are
recommended for Swanstone solid surface countertops.

Swanstone Product Care & Cleaning sample kits are
available through most Swanstone dealers.  The kits
include samples of approved cleaning products and
instructions.

Day-To-Day Cleanup

Wash regularly with warm water.  Use a soft cloth with a
mild detergent such as Handy Andy, Mr. Clean, or
Lestoil.  Always rinse off cleaners within five minutes of
application.  Scratch-free pads made of nylon, saran, or
polyethylene may be used.

To avoid damage to the surface, NEVER use steel wool
or metal scouring pads on Swanstone solid surface
material.

Hard to Remove Stains

Use abrasive cleaners such as Ajax, Bon Ami, or Bar
Keepers Friend or use an abrasive pad such as
Scotchbrite.

For the most stubborn sink stains, fill the swanstone sink
about one quarter full with a 50/50 solution of bleach
and water.  After 10 or 15 minutes of soaking, drain the
solution from the sink as you wash and rinse the sink.

Marks or Discolorations

White automotive rubbing compound may be used to
remove stubborn marks or discolorations.

Scratches

Use sandpaper, starting with 120 grit (coarsest) and
going to 220 grit and 320 grit until scratches disappear.  
Blend the area with an abrasive finishing pad, such as
Scotchbrite.

Use of the above products will not damage the
Swanstone solid surface material.  Always follow label
directions.  For more information on cleaning and
maintaining Swanstone products, contact the Swanstone
representative in your area.

Warranty

LIMITED WARRANTY

FOR RESIDENTIAL APPLICATIONS

If a Swan Corporation product covered by this warranty
is found to be defective in materials or workmanship,
after inspection by an authorized Swan Corporation
representative, we will repair, or at our option, exchange
the product for a similar model.  This warranty extends
for a designated period of time, so long as it remains in
use in its original place of installation.

This warranty covers products installed in accordance
with the Swan Corporation’s installation instructions,
used as recommended, and not damaged due to
misuse, abuse, or improper installation.  It does not
apply to any seams or changes made to the product by
professional tradesmen or fabricators.

The warranty applies only to the original purchaser and
installation of these products in residential applications.
It does not apply to commercial applications.

The Swan Corporation’s option to repair or exchange the
products under this warranty does not cover any labor or
other costs of removal or installation, nor shall the Swan
Corporation be responsible for any other incidental or
consequential damages attributable to a product defect
or to the repair or exchange of a defective product.

ALL IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE
WHICH EXCEED THE AFORESAID OBLIGATIONS
ARE HEREBY DISCLAIMED BY SELLER AND
EXCLUDED FROM THIS AGREEMENT

Limited Lifetime Warranty

ADA Lavatory Bowl

IMPORTANT NOTICE

IMPORTANT NOTICE

The Swan Corporation

14

800-325-7008

Maintenance

Summary of Contents for ULAD-1913

















Reviews: