manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Service Manual

The Suzuki Swift RS415 2017 Service Manual is available for free download on manualshive.com. This comprehensive manual includes detailed instructions and diagrams for vehicle maintenance and repairs. Get your hands on this essential manual to ensure your Suzuki Swift stays in top condition. Download it now!

Share
Download
background image

Wipers / Washers:  9D-4

Windshield Wiper Removal and Installation

S4RS0A9406012

Removal

1) Disconnect negative (–) cable at battery.
2) Remove wiper pivot caps (1) and wiper arm nuts (2), 

and remove windshield wiper arms with wiper blades 
(3).

3) Remove cowl top garnish referring to “Cowl Top 

Components:  in Section 9K”.

4) Disconnect coupler from windshield wiper motor.
5) Remove bolts (1), and remove windshield wiper 

assembly (2).

Installation

1) Install windshield wiper assembly (1), and tighten 

bolts to specified torque.

Tightening torque
Windshield wiper bolt (a):  8 N·m (0.8 kg-m, 6.0 
lb-ft)

2) Connect coupler to windshield wiper motor.

3) Install cowl top garnish referring to “Cowl Top 

Components:  in Section 9K”.

4) Install windshield wiper arms with wiper blades (1) to 

specified position as shown in figure, and then 
tighten windshield wiper nuts to specified torque.

Tightening torque
Windshield wiper arm nut (a):  16 N·m (1.6 kg-m, 
11.5 lb-ft)

5) Install wiper pivot caps (2) to windshield wiper arm 

nuts

6) Connect negative (–) cable to battery.

Windshield Wiper Motor Inspection

S4RS0A9406004

NOTE:
Make sure that battery voltage is 12 V or 
more.

 

1) Disconnect negative (–) cable at battery.
2) Remove windshield wiper arms with wiper blades 

referring to “Windshield Wiper Removal and 
Installation: ”.

3) Remove cowl top garnish referring to “Cowl Top 

Components:  in Section 9K”.

4) Disconnect coupler from windshield wiper motor.
5) Reinstall windshield wiper arms with wiper blade. For 

details, refer to Step 4) of “Installation” in “Windshield 
Wiper Removal and Installation: ”.

6) Check windshield wiper motor for operation as 

follows
• For motor operation in low speed

a. Connect battery positive (+) terminal to 

terminal “1” and its negative (–) terminal to 
terminal “5”.

b. Check if wiper arm reciprocation speed is as 

specification. If check result is not as 
specified, replace motor.

Specification
41 – 51 r/min (rpm)

1

3

3

2

I4RS0A940006-

I4RS0A940007-

I4RS0A940008-

3. Ceramic line
4. Wiper blade center

2

2

3

3

4

1

1

(a)

I4RS0A940009-

Summary of Contents for SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SWIFT RS415 2017

Suzuki SX4 SEDAN 2008 Owner'S Manual preview
SX4 SEDAN 2008
Brand: Suzuki Pages: 16
Harmar Mobility AL001 Installation And Owner'S Manual preview
AL001
Brand: Harmar Mobility Pages: 10
Jeep 2011 grand cherokee Accessories Quick Reference Manual preview
2011 grand cherokee
Brand: Jeep Pages: 22
Jeep 2013 Grand Cherokee Owner'S Manual preview
2013 Grand Cherokee
Brand: Jeep Pages: 704
Jeep 2012 Liberty Owner'S Manual preview
2012 Liberty
Brand: Jeep Pages: 558
PAC SWI-RC Installation Instructions preview
SWI-RC
Brand: PAC Pages: 4
PAC RP4-CH11 Manual preview
RP4-CH11
Brand: PAC Pages: 4
PAC BCI-CH41 User Manual preview
BCI-CH41
Brand: PAC Pages: 8
PAC C2R-CHY4 Installation Instructions preview
C2R-CHY4
Brand: PAC Pages: 5
Kuda-Phonebase 055040 Installation Instruction preview
055040
Brand: Kuda-Phonebase Pages: 3
Jacobsen Cushman Turf Truckster Parts & Maintenance Manual preview
Cushman Turf Truckster
Brand: Jacobsen Pages: 210
Alpine KCE-G7QI Installation preview
KCE-G7QI
Brand: Alpine Pages: 2
Whispbar K896W Fitting Instructions Manual preview
K896W
Brand: Whispbar Pages: 15
Roadmaster Sterling ALL-TERRAIN 576 Owner'S Manual & Installation Instructions preview
Sterling ALL-TERRAIN 576
Brand: Roadmaster Pages: 12
Toyota RX450h 2010 Emergency Response Manual preview
RX450h 2010
Brand: Toyota Pages: 35
Wilco Offroad UHG2060/AU Installation Manual preview
UHG2060/AU
Brand: Wilco Offroad Pages: 4
AA Products RB0007 Instruction Manual preview
RB0007
Brand: AA Products Pages: 6
Unex OBU-352EC Quick Start Manual preview
OBU-352EC
Brand: Unex Pages: 30

Brands by name

Popular brands

Load more brands