Suzuki SMD7 Installation Manual Download Page 1

All brand and product names are trademarks, registered trademarks or service marks of their respective holders.

Installation Manual

IMPORTANT NOTICES AND SAFETY INSTRUCTIONS ..........i
SYSTEM CONFIGURATION ....................................................iii
EQUIPMENT LIST ....................................................................iv

1. INSTALLATION....................................................................1

1.1 Disply Unit Installation..................................................................1
1.2 Radar Sensor (DRS4W) Installation............................................4
1.3 Transducer Installation................................................................5
1.4 Speed/Temperature Sensor (Option) Installation......................14

2. WIRING...............................................................................15

2.1 Power/NMEA0183 Port.............................................................15
2.2 XDR Port.....................................................................................16
2.3 NMEA2000 (CAN bus) Connections..........................................17

3. SETTINGS AND ADJUSTMENTS .....................................18

3.1 Starting the Setup Procedure.....................................................18
3.2 How to Use the Menu................................................................19
3.3 Initial Setup Menu.......................................................................20
3.4 How to Set up the SUZUKI Gateway.........................................24
3.5 SMD 7/9 Connection Examples of Various Systems.................28
3.6 How to Set Up the Fish Finder...................................................36
3.7 How to Set Up the Radar...........................................................37   

4. INPUT/OUTPUT DATA........................................................39

4.1 How to access the [Interface] menu...........................................39
4.2 How to set up for NMEA0183 configurations .............................39
4.3 How to select a data source.......................................................39
4.4 How to select which NMEA2000 data to output.........................40
4.5 How to select which NMEA0183 sentence to output .................40
4.6 How to calibrate (offset) the sensors .........................................41
4.7 How to reset the [Interface] menu..............................................42
4.8 NMEA0183/NMEA2000 Monitor.................................................42

5. MAINTENANCE AND TROUBLESHOOTING ....................43

5.1 General Maintenance.................................................................44
5.2 Life of Parts................................................................................44
5.3 Troubleshooting .........................................................................44
5.4 How to Restore the Default Settings..........................................46
5.5 How to View the System Information .........................................46

APPENDIX 1 MENU TREE ..................................................AP-1
APPENDIX 2 RADIO REGULATORY  INFORMATION ......AP-9
SPECIFICATIONS ................................................................SP-1

OUTLINES ..............................................................................D-1
INTERCONNECTION..............................................................S-1

Multi-Function Display

Model

 SMD7/SMD9

PACKING LISTS.....................................................................A-1

Summary of Contents for SMD7












































Reviews: