manualshive.com logo in svg

Suzuki SMD12, Operator'S Manual, Page: 34 / 338

Share
Download
Suzuki SMD12 Operator'S Manual Download Page 34

1.  SYSTEM INTRODUCTION

1-17

1.7.2

How to edit the display icon

Long tap the display icon to edit to show the editing icons on the display icon. Tap the 
applicable editing icon. Refer to the figure and instructions below.

Edit icon content

: Tap the icon at the upper left corner. See the illustration in 

paragraph 1.7.1 for how to set the icon.

Remove icon

: Tap the icon at the upper right corner to remove the icon from the home 

screen (and quick page if the icon size is selected to "large".

Change icon size

: Tap the icon at the lower right corner to switch the size between 

large and small. (Icons set for large size appear on the quick page.)

Long

tap

Remove icon

Change icon size

Edit icon content

Summary of Contents for SMD12



















































































































































































































































































































































Reviews:

No comments