manualshive.com logo in svg

Suzuki SMD12, Operator'S Manual

The Suzuki SMD12 Operator's Manual is the essential companion for any Suzuki SMD12 owner. With easy-to-follow instructions and detailed diagrams, this manual guides users through every aspect of operating and maintaining their SMD12. Download it for free from our website now and unlock the full potential of your Suzuki SMD12.

Share
Download
background image

3.  PLOTTER

3-24

3.12

Plotter Menu

This section describes the [Plotter] menu items, which are in the [Settings] - [Plotter] 
menu.

[Grid Interval]

: Set the distance between grid lines. The options are [Off] (no lines), 

[Very Small], [Small], [Medium], [Large], and [Very Large].

[Show Scale Slider]

: Show or hide the scale slider.

[Tide/Current Icons Size]

: Set the size of the icon for tide and current.

[Transparencies]

[NavData Transparency]

: Set the degree of transparency for the navdata display. 

[PhotoFusion Transparency]

: Set the degree of transparency for the satellite photo 

overlay.

[Tide Range for PhotoFusion]

: Set the degree of transparency for the tide range in 

the satellite photo overlay.

[Tidal Currents Transparency]

: Set the degree of transparency for the tidal currents 

display.

[Radar Overlay]

[Radar Transparency]

: Set the degree of transparency for the radar echo.

Summary of Contents for SMD12



















































































































































































































































































































































Reviews:

No comments

Related manuals for SMD12

Panasonic CYVMX6800U - 6.8" CLR MONITOR/DVD Operating Instructions preview
CYVMX6800U - 6.8" CLR MONITOR/DVD
Brand: Panasonic Pages: 4
Garmin VIVOSMART HR Owner'S Manual preview
VIVOSMART HR
Brand: Garmin Pages: 16
Samsung SyncMaster P2450H Manual Del Usuario preview
SyncMaster P2450H
Brand: Samsung Pages: 44
Samsung SyncMaster P42H-2 Quick Start Manual preview
SyncMaster P42H-2
Brand: Samsung Pages: 26
NewCommWorld NLM155A1 Operation Manual preview
NLM155A1
Brand: NewCommWorld Pages: 19
I-Tech NQW922 User Manual preview
NQW922
Brand: I-Tech Pages: 50
A&D SMARTMETER iBloodPressure 2.0 Instruction Manual preview
SMARTMETER iBloodPressure 2.0
Brand: A&D Pages: 32
Hansol 920A User Manual preview
920A
Brand: Hansol Pages: 8
inbody BPBIO320 User Manual preview
BPBIO320
Brand: inbody Pages: 44
Eachine LCD5802D User Manual preview
LCD5802D
Brand: Eachine Pages: 4
Mitsubishi Diamond Pro 700 TFK9705SKHKW User Manual preview
Diamond Pro 700 TFK9705SKHKW
Brand: Mitsubishi Pages: 64
3M 11-81336-225 - MicroTouch M150 High... User Manual preview
11-81336-225 - MicroTouch M150 High...
Brand: 3M Pages: 35
i3TOUCH V-SENSE 8404 4K T10 User Manual preview
V-SENSE 8404 4K T10
Brand: i3TOUCH Pages: 53
Dante DLV6230-26 Installation And Operation Manual preview
DLV6230-26
Brand: Dante Pages: 10
Mi RMMNT238NF User Manual preview
RMMNT238NF
Brand: Mi Pages: 11
G-STORY GS156HR User Manual preview
GS156HR
Brand: G-STORY Pages: 35
AOC Adelpia SAT22LAN Service Manual preview
Adelpia SAT22LAN
Brand: AOC Pages: 91
Soon CARE SBM-010WP User Manual preview
CARE SBM-010WP
Brand: Soon Pages: 30

Brands by name

Popular brands

Load more brands