Suzuki LT-A750X/P Supplementary Service Manual Download Page 90

Page: 90 / 136

6C-21 Power Assisted Steering System:

3) Read the DTC (Diagnostic Trouble Code) and show

data when trouble (displaying data at the time of
DTC) according to instructions displayed on SDS.

NOTE

• Not only is SDS used for detecting

Diagnostic Trouble Codes but also for
reproducing and checking on screen the
failure condition as described by
customers using the trigger.

• How to use trigger. (Refer to the SDS

operation manual for further details.)

• When DTC is checked, DTC “C1122” is

displayed with ignition switch turned ON.
However, if the engine is started and the
display disappears, it is not a trouble.

4) Close the SDS tool and turn the ignition switch OFF.

DTC (Diagnostic Trouble Code) Deleting (LT-
A750XP/ZK9)

B931G36304005

Use of Mode Select Switch

1) Remove the seat. Refer to “Seat Removal and

Installation in Section 9D in related manual”.

2) Connect the special tool to the mode select coupler

and output the DTCs.

Special tool

(A): 09930–82720 (Mode selection switch)

(A)

(B)

I705H1110116-03

I931H1630032-01

I931G3630020-01

(A)

I931G3630021-01

Summary of Contents for LT-A750X/P









































































































































Search results

Summary of Contents for LT-A750X/P

Reviews:

Related manuals for LT-A750X/P

Brands by name

Popular brands

Suzuki LT-A750X/P, Supplementary Service Manual

Search results

Summary of Contents for LT-A750X/P

Reviews:

Related manuals for LT-A750X/P

Brands by name

Popular brands