Engine Mechanical: 1D-46
Main Bearings, Crankshaft and Cylinder Block
Removal and Installation
S3RH0A1406040
Removal
1) Remove engine assembly from vehicle referring to
“Engine Assembly Removal and Installation”.
2) Remove clutch cover, clutch disc and flywheel (drive
plate for A/T) by using special tool.
Special tool
(A): 09924–17811
3) Remove intake manifold and exhaust manifold
referring to “Throttle Body and Intake Manifold
Removal and Installation” and “Exhaust Manifold
Removal and Installation in Section 1K”.
4) Remove oil pan and oil pump strainer referring to “Oil
Pan and Oil Pump Strainer Removal and Installation
in Section 1E”.
5) Remove cylinder head cover referring to “Cylinder
Head Cover Removal and Installation”.
6) Remove timing chain cover referring to “Timing
Chain Cover Removal and Installation”.
7) Remove timing chain guide, chain tensioner
adjuster, chain tensioner, timing chain and
crankshaft timing sprocket referring to “Timing Chain
and Chain Tensioner Removal and Installation”.
8) Remove crankshafts, tappets and shims referring to
“Camshaft, Tappet and Shim Removal and
installation”.
9) Remove cylinder head assembly referring to “Valves
and Cylinder Head Removal and Installation”.
10) Remove pistons and connecting rods referring to
“Pistons, Piston Rings and Connecting Rods
Removal and Installation”.
11) Remove rear oil seal housing (1).
12) Loosen bearing cap No.1 and No.2 bolts in such
order as indicated in the figure and remove them.
13) Remove crankshaft from cylinder block.
1. CKP sensor (if equipped)
: See “A”
9. Thrust bearing
17. Main bearing mounting No.2 bolt
: Tighten 22 N
⋅
m (2.2 kgf-m, 16.0 lb-ft) by the specified
procedure.
2. Knock sensor
10. Rear oil seal housing
: See “B”
18. Main bearing mounting No.1 bolt
: Make sure main bearing mounting No.1 bolt deformation
when reuse it due to plastic deformation tightening referring to
“Main Bearings Inspection”.
: Tighten 30 N
⋅
m (3.0 kgf-m, 22.0 lb-ft), 50 N
⋅
m (5.0 kgf-m,
36.5 lb-ft) and 60
°
by the specified procedure.
3. Cylinder block
11. Rear oil seal
19. O-ring
4. Venturi plug
12. Input shaft bearing
20. Oil filter adapter case
5. Main bearing
13. Flywheel
21. Oil filter adapter bolt
“A”: When installing CKP sensor, use new sensor mounting bolt.
: Tightening torque
“B”: Apply sealant 99000-31250 to mating surface.
: Do not reuse.
“C”: Apply sealant 99000-31110 to thread part.
: Apply engine oil to inside / sliding surface.
I2RH0B140125-01
I2RH0B140126-01
I2RH0B140127-01
Summary of Contents for Liana RH413
