IQNITER SMART SENSOR
USER GUIDE
CAUTION: Do not pull the iQniter
Smart Sensor module off the belt.
This may damage the belt connectors.
Unsnap one side at a time.
CAUTION: Do not machine wash
the iQniter Smart Sensor module.
Machine washing damages the
module.
NOTE: Both the iQniter Smart Sensor
module and belt should be rinsed
with fresh water after each use. The
belt should be machine washed
in 40º C after every 2-3 exercises.
See the belt tag for further washing
instructions.
NOTE: You do not need to replace the
iQniter Smart Sensor module; only
the Suunto Smart Sensor belt strap
may eventually need replacing after
extended use.
NOTE: Dry skin under the belt
electrodes, a loose belt, and synthetic
shirt materials can cause abnormally
high heart rate readings. Moisten the
belt electrodes well and tighten the
belt to avoid heart rate peaks. If you
are otherwise concerned about your
heart rate, please consult a doctor.
NOTE: When changing battery, we
strongly recommend using a new
original cover to ensure proper
sealing and avoid moist inside the
sensor
NOTE: Limited warranty 1 year. For
personal use only. I case the usage
pattern holds multi-user application,
the warranty is void.
The iQniter Smart Sensor uses a 3-Volt lithium cell CR2025. With Suunto
Movescount App, you can check the battery status from the device information
when the iQniter Smart Sensor is paired.
REPLACING THE BATTERY
1
Remove the sensor firmly from the belt
2
Open the battery cover
3
Replace the battery (Smart Sensor CR2025). Ensure that the battery switch
(red arrow 3) is NOT UNDER the battery.
4
Place the new cover with sealing ring. First inset the cover in the battery
switch side (red arrow 4)
5
Firmly close the battery cover (red arrow 5)
Note: We recommend always to use a new cover to ensure a prober sealing
when replacing battery
WARNING: Only for recreational use.
WARNING: Always consult your doctor before beginning an exercise program.
Overexertion may cause serious injury.
WARNING: Allergic reactions or skin irritations may occur with any product
that is in contact with skin, even though our products comply with all industry
standards. In such event, stop use immediately and seek medical attention.
WARNING: People who have a pacemaker, defibrillator, or other implanted
electronic device use the transmitter belt at their own risk. Before starting
the initial use of the heart rate belt, we recommend an exercise test under a
doctor’s supervision. This will ensure the safety and reliability of the pacemaker
and heart rate belt when being used simultaneously. Exercise may include
some risk, especially for those who have been sedentary. We strongly advise
you to consult your doctor prior to beginning a regular exercise program.
CARE AND SUPPORT
COMPLIANCE
SAFETY
BATTERY
EU radio directive
Hereby, Suunto Oy, declares that the
radio equipment type MOVESENSE is
in compliance with Directive 2014/53/
EU. The full text of the EU declaration
of conformity is available at the
following internet address:
www.Suunto.com/EUconformity.
FCC
This device complies with Part 15 of
the FCC Rules. Operation is subject
to the following two conditions: (1)
this device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may
cause undesired operation. This
product has been tested to comply
with FCC standards and is intended
for home or office use. Changes or
modifications not expressly approved
by Suunto could void your authority
to operate this device under
FCC regulations.
IC
This device complies with Industry
Canada licence-exempt RSS
standard(s). Operation is subject to
the following two conditions: (1) this
device may not cause interference,
and (2) this device must accept any
interference, including interference
that may cause undesired operation
of the device.
Cet appareil est conforme aux
normes RSS hors licence d’Industrie
Canada. Son utilisation est soumise
aux deux conditions suivantes:
(1) cet appareil ne doit pas causer
d’interférences, (2) cet appareil
doit accepter toute interférence, y
compris les interférences pouvant
entraîner un fonctionnement non
désiré de l’appareil.
© Suunto Oy 2018. All rights reserved.
Suunto is a registered trademark of Suunto Oy.
3
4
5
TROUBLESHOOTING
CHECK YOUR BELT
■
Electrodes must be moist and in proper contact with skin. Unstable HR signals
may be due to dry skin contact with belt. In some cases it may be necessary to
move the strap a bit to get connected.
■
Ill-fitting strap, too lose against skin and electrode loses contact with skin
■
Strap not over heart, ensure sensor is in center of chest and electrodes in
contact with skin directly under breast line
■
Strap can provide years of use if properly cared for, however it will wear and
need replacing
■
Low battery (life is approximately 200 hours with normal use)
■
Damaged Sensor contacts (with care remove one contact at a time, don’t push
the sensor/transmitter from the belt)
■
The elastic strap has a max strench of 15 %. Different strap sizes are available.
TROUBLESHOOTING IN THE GYM
For troubleshooting when you use the iQniter Smart Sensor together with iQniter
Cardio Training in the gym, please follow this additional guide line:
1
Check that the sensor ID is correctly registered at my.iqniter.com or in the
AdmiQ-registrationprogram at the gym.
2
Cardio Training related troubleshooting (consult the instructor or reception in
the gym. Refer to installation guide at www.iqniter.com.)
Please note that iQniter Cardio Training only works with “
Q
” Smart Sensors
(white front). Suunto Smart Sensors (black front) are not applicable.
#iqniter
#iqniter
GET SOCIAL!
