Sutter Instrument Lambda HPX Operation Manual Download Page 6 | Manualshive

Page: 6 / 36

Sutter Instrument Lambda HPX Operation Manual Download Page 6

4

Operate only in a location where there is a free flow of fresh air on all sides.
NEVER ALLOW THE FREE FLOW OF AIR TO BE RESTRICTED.

This instrument is designed for operation in a laboratory environment (Pollution Degree
I) that is free from mechanical vibrations, electrical noise and transients.

DO NOT CONNECT OR DISCONNECT THE CABLES AND TUBING BETWEEN

THE HPX AND THE HIGH-POWER LED ASSEMBLY WHILE POWER IS ON.

Operate this instrument only according to the instructions included in this manual.

Do not operate if there is any obvious damage to any part of the instrument.

Do not operate this instrument near flammable materials. The use of any hazardous

materials with this instrument is not recommended and, if undertaken, is done so at the
users’ own risk.

Do not operate if there is any obvious damage to any part of the instrument.

LAMBDA HPX HIGH-POWER LED LIGHT SOURCE SYSTEM OPERATION MANUAL – REV. 1.03E (20141208)

«
...
4
5
6
7
8
...
»

Summary of Contents for Lambda HPX





































Reviews:

No comments