Sutter Instrument Lambda DG-4 Operation Manual Download Page 5

Page: 5 / 86

LAMBDA DG-4 & DG-5 OPERATION MANUAL – REV.

3.05C

(

20150414

)

iii

DISCLAIMER

The ultra high speed wavelength switching xenon arc lamp Lambda DG-4/5 system is

designed for the specific use as a microscope illuminator and optical wavelength switcher, and

no other use is recommended.
This instrument should only be used in a laboratory environment for use on animal tissues.

It is not intended for, nor should it be used in, human experimentation or applied to humans

in any way. This is not a medical device.
Do not open or attempt to repair the instrument without expressed and explicit instructions

from Sutter Instrument Company. Extreme heat and high voltages are present and could

cause injury.
Do not allow unauthorized and or untrained operatives to use this device.
Any misuse will be the sole responsibility of the user/owner and Sutter Instruments assumes

no implied or inferred liability for direct or consequential damages from this instrument if it

is operated or used in any way other than for which it is designed.

SAFETY WARNINGS AND PRECAUTIONS
Electrical

Operate the Lambda DG-4/5 using 110-120 V AC, 60 Hz, or 220-240 V AC., 50 Hz line

voltage. This instrument is designed for connection to a standard laboratory power outlet

(Overvoltage Category II), and because it is a microprocessor--controlled device, it should

be accorded the same system wiring precautions as any 'computer type' system. A surge

protector and power regulator are recommended.

Fuse Replacement: Replace only with the same type and rating:

5 x 20 mm glass tube, time delay (medium), time lag, or “slow blow”)
Rating:

Line Voltage: 100 - 120VAC

(Voltage Switch Setting: 110V)

Line Voltage: 220 - 240VAC

(Voltage Switch Setting: 220V)

Manufacturer Examples

RoHS Compliant (Lead Free)?

Xenon

Lamp

Power

Rating

Fuse

Rating

Yes No

Fuse

Rating

Yes No

125

Watts

3.0A,

125V

Bussmann: GMC-3-R

Littelfuse: 239 003.P

Bussmann: GMC-3A

Littelfuse: 239 003

T2.0A,

250V

Bussmann: S506-2-R
Littelfuse: 218 002.P

Bussmann: GDC-2A

Littelfuse: 218 002

175

Watts

4.0A,
125V

Bussmann: GMC-4-R

Littelfuse: 239 004.P

Bussmann: GMC-4A

Littelfuse: 239 004

300

Watts

5.0A,
125V

Bussmann: GMC-5-R

Littelfuse: 239 005.P

Bussmann: GMC-5A

Littelfuse: 239 005

T3.15A,

250V

Bussmann: S506-315-R

Littelfuse: 218 3.15P

Bussmann: GDC-3.15A

Littelfuse: 218 3.15

A spare fuse is located in the power input module. Please refer to the fuse-replacement

appendix for more details on fuse ratings and for instructions on how to change the fuse.

NOTE: The 125-Watt lamp version of the DG-4/DG-5 is a discontinued product.

Summary of Contents for Lambda DG-4























































































Search results

Summary of Contents for Lambda DG-4

Reviews:

Related manuals for Lambda DG-4

Brands by name

Popular brands

Sutter Instrument Lambda DG-4, Operation Manual

Search results

Summary of Contents for Lambda DG-4

Reviews:

Related manuals for Lambda DG-4

Brands by name

Popular brands