• Protection against electric shock: Class II including AC/DC Adapter.
• Applied parts : No applied parts.
• Protection against harmful ingress of water: ordinary IPXO.
Direct current
Class II
equipment
CE mark
Serial No.
Alternating
current
Attention, consult
accompanying
documents
CLASSIFICATION
Storing the LED system in a safe place will prolong the life of the unit. The
following guidelines will help in sustaining the LED systems useful life:
• Keep the optical face on the light unit from touching hard surfaces which may
cause scratches on the surface. Scratches on the surface will diminish the light
quality.
• When cuts or punctures are visible on the system’s light cord, the wireless LED
system is no longer safe to use; it should be taken out of service immediately.
MAINTENANCE
• Do not immerse in water or any liquid; wipe down with damp cloth. Do not use
HOT or COLD water; using “room-temperature” water is acceptable
• Avoid using running water and disinfectant sprays on or near open slots located
on light unit. Carefully wiping with damp cloth is ok.
• Do not use Lysol® or any disinfectants containing glutaraldehydes, iodophors,
ammonia, alcohol, or ethanol
• Do not autoclave
Disinfection: Use SciCan® “OPTIM 33 TB” wipes/solution only.
*Note: SciCan® OPTIM 33 TB solution can be purchased through SurgiTel in 8 oz.
bottles
FACTORY REFURBISHMENT CLEANING: is available if you come across a difficult
cleaning situation. Call customer support for details: 800-959-0153
*IMPORTANT*
CLEANING
OPERATION
Dove Tail
Adapter
Clip
Adapter
(provided w/
kit)
ATTACHING LIGHT ADAPTER TO LOUPE
• Charge Time = approximately 2 hours
• Charge Level Indicator Lights (3 qty., color: blue): All 3 lights on = fully charged
• Maximum continuous operation ( 1 battery) from full power is approximately
1.75 hours
Note: To maximize use of Wireless LED, remember to replace and charge battery
after use
• Attach the LED light to loupes or glasses using appropriate adapter
H
I
J
Optional Light Adapter Assembly (H)
:
Recommended option if experiencing attachment difficulties or alignment
issues with loupe, remove screw and reassemble by changing the light
adapter position (as shown)
Vertical Alignment #1 (I)
:
Maximum range of adjustment for light system placement
Vertical Alignment #2 (J)
:
Minimal range of adjustment for fine tuning light beam position
CAUTION: Do not apply too much force when adjusting, this action can lead
to light cord damage
ADJUSTMENTS
RECHARGEABLE BATTERIES
(push click to charge/eject battery)
Charge Level
Indicator
Note about light-cured composites
• Although it is not recommended to use this LED Light while working with
light-cured composites, setting the light to a lower light intensity may allow
you to work briefly with materials before hardening
• Using the appropriate COLOR FILTER (orange filter) is STRONGLY
RECOMMENDED when using light-cured materials with the LED Light
• Ambient temperature range 10 to 40
o
C
• Relative humidity range 30 to 75%
• Atmospheric pressure range 70 to 106 kPa
• Ambient temperature range -40 to 70
o
C
• Relative humidity range 10 to 100%
• Atmospheric pressure range 50 to 106 kPa
OPERATING CONDITION
TRANSPORT & STORAGE CONDITION
Fixing Hinge Tension (too loose or too tight):
Step 1: Use provided hex key to remove hinge
set screw (see photo to the right)
Step 2: Use two flat-head screwdrivers (placed
on each side) to loosen/tighten special
screw and nut
Step 3
: Once desired tension is met,
reassemble and tighten set screw
HOW TO TURN LIGHT ON AND OFF
1. Touch on/off symbol (D) or anywhere on control panel to turn light on or off
2. To lock light in the on/off position, touch lock symbol (C) with your finger
and hold until you hear one beep. To restore use of power switch, hold lock
symbol (C) again until same beep is heard
HOW TO SET BRIGHTNESS OF LIGHT
1. Touch light symbol (E) with your finger and hold until you hear two beeps,
at this point the indicator light (A) will show purple. This means the
brightness can now be adjusted.
• To increase brightness of light, touch plus symbol (B) (3 brightness
options)
• To decrease brightness of light, touch minus symbol (F)
2. To lock brightness setting, hold light symbol (E) until you hear two beeps
and purple
indicator light is not visible (A)
SYSTEM RESET
Unscrew battery and reassemble (G). This action will restore the system to the
original settings.
G
A
B
C
D
E
F
