IMPORTANT
Check whether it concerns an AC(Alterna
Ɵ
ng Current) based system - 100-240V/277V AC, 50/60Hz.
This marking indicates that this product should not be disposed with other household wastes throughout the EU.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return your used device, please use
the return and collec
Ɵ
on systems or contact the retailer where the product was purchased. They can take
this product for environmental safe recycling.
ELECTRICAL CONNECTIONS - 100-240V/277V AC, 50/60Hz
PHASE TO NEUTRAL WIRING
STEP 1:
Make the following Electrical Connec
Ɵ
ons:
a.
b.
c.
Connect
INPUT GROUND
conductor to
GREEN WIRE
posi
Ɵ
on
of the terminal block or GROUND conductor of LED driver.
Connect
INPUT VOLTAGE
conductor to
BROWN WIRE
posi
Ɵ
on
of the terminal block or LINE conductor of LED driver.
Connect
INPUT NEUTRAL
conductor to
BLUE WIRE
posi
Ɵ
on
of the terminal block or NEUTRAL conductor of LED driver.
STEP 2:
Make sure all excess input wires are pushed into pole, screws are
Ɵ
ghtened.
STEP 3:
Close cover by
fi
rmly pushing cover towards
fi
xture, making sure
that no wires are pinched and Sealing gasket are fully engaged.
STEP 4:
If the
fi
xture without a terminal block, please insulate all electrical
connec
Ɵ
ons with wire nuts suitable for at least 90°C
TERMINAL BLOCK(not-provided),
Use waterproof connector for wet loca
Ɵ
on.
LED DRIVER
GROUND
GREEN
NEUTRAL
WHITE
NEUTRAL
BLUE
GROUND
YELLOW-GREEN
LINE
BLACK
LINE
BROWN
L
G
N
INPUT WIRING
FIXTURE WIRING
AC BASED
Input cable should be at least H05RN-F 3x1.0mm²(SJTW 18AWG) or
outdoor grade cable with rubber sheathed(not supplied). The cable
must have a minimum cross sec
Ɵ
onal area of 1.0mm²(18AWG).
*If the
fi
xture with built-in 3 in 1 dimming func
Ɵ
on, please connect INPUT
PO) signal conductor to DIM+ (BLUE WIRE), INPUT NEGATIVE(-) signal
conductor to DIM-(WHITE WIRE) of LED driver.
WWW.SUREFINEGROUP.COM
Loosen the moun
Ɵ
ng bracket screws, adjust
the
fi
xture to desire posi
Ɵ
on, re-secure the
screws.
STEP 3:
Connect the
Power Cord
to the supply wiring
per “
Electrical Connec
Ɵ
ons
” sec
Ɵ
on for
comple
Ɵ
ng electrical connec
Ɵ
ons.
STEP 4:
PENDANT MOUNTING
Assemble the moun
Ɵ
ng bracket to the
fi
xture
by provided M10 (3/8”) round head screws.
STEP 1:
A
Ʃ
ach Lock-Nut(A) to the bo
Ʃ
om of the
Pendant Stem. A
Ʃ
ach Lock-Nut(B) by holding
the interjacent Fixture Bracket and
Ɵ
ghtening
Lock-Nut(B) un
Ɵ
l secure. See
Figure 4.
STEP 2:
4
5
Look-Nut(A)*²
Look-Nut(B)*²
Pendant Stem*¹
Pendant Stem Thread
*¹ Pendant Stem can not be the so
Ō
material (not-provided)
*² Look Nuts are not provided
Power Cord
(Cord Not shown)
Power Cord
(Cord Not shown)
